C8051F131R Silicon Labs, C8051F131R Datasheet - Page 280

• Manufacturer Part Number: C8051F131R
• Description: 8-bit Microcontrollers - MCU 128kB 100MIPS 8448B RAM
• Manufacturer: Silicon Labs

Specifications of C8051F131R

• Product Category: 8-bit Microcontrollers - MCU
• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 100 MHz
• Program Memory Size: 128 KB
• Data Ram Size: 8.25 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 3.6 V
• Package / Case: TQFP-64
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 9
• Data Rom Size: 64 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 32
• Number Of Timers: 16 bit
• Processor Series: C8051
• Program Memory Type: Flash
• Factory Pack Quantity: 500
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 3 V

C8051F120/1/2/3/4/5/6/7
C8051F130/1/2/3
20.6. SPI Special Function Registers
SPI0 is accessed and controlled through four special function registers in the system controller: SPI0CN
Control Register, SPI0DAT Data Register, SPI0CFG Configuration Register, and SPI0CKR Clock Rate
Register. The four special function registers related to the operation of the SPI0 Bus are described in the
following figures.
280
*Note:
Bit 7:
Bit 6:
Bit 5:
Bit 4:
Bit 3:
Bit 2:
Bit 1:
Bit 0:
SPIBSY
Bit7
R
SPIBSY: SPI Busy (read only).
This bit is set to logic 1 when a SPI transfer is in progress (Master or slave Mode).
MSTEN: Master Mode Enable.
0: Disable master mode. Operate in slave mode.
1: Enable master mode. Operate as a master.
CKPHA: SPI0 Clock Phase.
This bit controls the SPI0 clock phase.
0: Data centered on first edge of SCK period.*
1: Data centered on second edge of SCK period.*
CKPOL: SPI0 Clock Polarity.
This bit controls the SPI0 clock polarity.
0: SCK line low in idle state.
1: SCK line high in idle state.
SLVSEL: Slave Selected Flag (read only).
This bit is set to logic 1 whenever the NSS pin is low indicating SPI0 is the selected slave. It
is cleared to logic 0 when NSS is high (slave not selected). This bit does not indicate the
instantaneous value at the NSS pin, but rather a de-glitched version of the pin input.
NSSIN: NSS Instantaneous Pin Input (read only).
This bit mimics the instantaneous value that is present on the NSS port pin at the time that
the register is read. This input is not de-glitched.
SRMT: Shift Register Empty (Valid in Slave Mode, read only).
This bit will be set to logic 1 when all data has been transferred in/out of the shift register,
and there is no new information available to read from the transmit buffer or write to the
receive buffer. It returns to logic 0 when a data byte is transferred to the shift register from
the transmit buffer or by a transition on SCK.
NOTE: SRMT = 1 when in Master Mode.
RXBMT: Receive Buffer Empty (Valid in Slave Mode, read only).
This bit will be set to logic 1 when the receive buffer has been read and contains no new
information. If there is new information available in the receive buffer that has not been read,
this bit will return to logic 0.
NOTE: RXBMT = 1 when in Master Mode.
on MISO is sampled one SYSCLK before the end of each data bit, to provide maximum
settling time for the slave device. See Table 20.1 for timing parameters.
In slave mode, data on MOSI is sampled in the center of each data bit. In master mode, data
MSTEN
R/W
Bit6
SFR Definition 20.1. SPI0CFG: SPI0 Configuration
CKPHA
R/W
Bit5
CKPOL
R/W
Bit4
SLVSEL
Rev. 1.4
Bit3
R
NSSIN
Bit2
R
SRMT
Bit1
R
SFR Address:
RXBMT
SFR Page:
Bit0
R
0x9A
0
Reset Value
00000111