TMP86xy92DMG Toshiba, TMP86xy92DMG Datasheet - Page 30

• Manufacturer Part Number: TMP86xy92DMG
• Manufacturer: Toshiba

Specifications of TMP86xy92DMG

• Package: SSOP30
• Rom Types (m=mask,p=otp,f=flash): M/F
• Rom Size: 16
• Ram Size: 512
• Driver Led: 8
• Driver Lcd: -
• Spi/sio Channels: 1
• Uart/sio Channels: 2
• I2c/sio Channels: 1
• High-speed Serial Output: -
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 6
• Da Converter Channels: -
• Timer Counter 18-bit Channel: -
• Timer Counter 16-bit Channel: 1
• Timer Counter 8-bit Channel: 2
• Motor Channels: -
• Watchdog Timer: Y
• Dual Clock: Y
• Clock Gear: -
• Number Of I/o Ports: 24
• Power Supply (v): 4 to 5.5

2.2
System Clock Controller
2.2.4
System Control Register 1
System Control Register 2
SYSCR1
SYSCR2
(0038H)
(0039H)
Note 1: Always set RETM to “0” when transiting from NORMAL mode to STOP mode. Always set RETM to “1” when transiting
Note 2: When STOP mode is released with RESET pin input, a return is made to NORMAL1 regardless of the RETM contents.
Note 3: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz], *; Don’t care
Note 4: Bits 0 and 1 in SYSCR1 are read as undefined data when a read instruction is executed.
Note 5: As the hardware becomes STOP mode under OUTEN = “0”, input value is fixed to “0”; therefore it may cause external
Note 6: When the key-on wakeup is used, RELM should be set to "1".
Note 7: In case of setting as STOP mode is released by a rising edge of STOP pin input, the release setting by STOP5 to STOP2
Note 8: Port P20 is used as STOP pin. Therefore, when stop mode is started, OUTEN does not affect to P20, and P20 becomes
Note 9: The warming-up time should be set correctly for using oscillator.
Note 1: A reset is applied if both XEN and XTEN are cleared to “0”, XEN is cleared to “0” when SYSCK = “0”, or XTEN is cleared
Note 2: *: Don’t care, TG: Timing generator.
Note 3: Bits 3, 1 and 0 in SYSCR2 are always read as undefined value.
Operating Mode Control
STOP
TGHALT
XEN
SYSCK
OUTEN
from SLOW mode to STOP mode.
interrupt request on account of falling edge.
on STOPCR register is prohibited.
High-Z mode.
to “0” when SYSCK = “1”.
XTEN
RETM
STOP
RELM
IDLE
7
7
XEN
WUT
RELM
XTEN
High-frequency oscillator control
Low-frequency oscillator control
Main system clock select (Write)/
main system clock monitor
(Read)
CPU and watchdog timer control
(IDLE1/2 and SLEEP1/2 modes)
TG control (IDLE0 and SLEEP0
modes)
6
6
STOP mode start
Release method for STOP
mode
Operating mode after STOP
mode
Port output during STOP mode
Warm-up time at releasing
STOP mode
SYSCK
RETM
5
5
OUTEN
IDLE
4
4
0: CPU core and peripherals remain active
1: CPU core and peripherals are halted (Start STOP mode)
0: Edge-sensitive release
1: Level-sensitive release
0: Return to NORMAL1/2 mode
1: Return to SLOW1 mode
0: High impedance
1: Output kept
0: Turn off oscillation
1: Turn on oscillation
0: Turn off oscillation
1: Turn on oscillation
0: High-frequency clock (NORMAL1/NORMAL2/IDLE1/IDLE2)
1: Low-frequency clock (SLOW1/SLOW2/SLEEP1/SLEEP2)
0: CPU and watchdog timer remain active
1: CPU and watchdog timer are stopped (Start IDLE1/2 and SLEEP1/2 modes)
0: Feeding clock to all peripherals from TG
1: Stop feeding clock to peripherals except TBT from TG.
(Start IDLE0 and SLEEP0 modes)
3
3
00
01
10
11
WUT
Page 16
TGHALT
2
2
Return to NORMAL mode
3 x 2
3 x 2
1
1
2
2
16
14
/fc
/fc
16
14
/fc
/fc
0
0
(Initial value: 0000 00**)
(Initial value: 1000 *0**)
Return to SLOW mode
3 x 2
3 x 2
TMP86FH92DMG
2
2
13
6
/fs
/fs
13
6
/fs
/fs
R/W
R/W
R/W
R/W
R/W
R/W
R/W