TMP86xy92DMG Toshiba, TMP86xy92DMG Datasheet - Page 109

• Manufacturer Part Number: TMP86xy92DMG
• Manufacturer: Toshiba

Specifications of TMP86xy92DMG

• Package: SSOP30
• Rom Types (m=mask,p=otp,f=flash): M/F
• Rom Size: 16
• Ram Size: 512
• Driver Led: 8
• Driver Lcd: -
• Spi/sio Channels: 1
• Uart/sio Channels: 2
• I2c/sio Channels: 1
• High-speed Serial Output: -
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 6
• Da Converter Channels: -
• Timer Counter 18-bit Channel: -
• Timer Counter 16-bit Channel: 1
• Timer Counter 8-bit Channel: 2
• Motor Channels: -
• Watchdog Timer: Y
• Dual Clock: Y
• Clock Gear: -
• Number Of I/o Ports: 24
• Power Supply (v): 4 to 5.5

Example :Generating a pulse which is high-going for 800 μs and low-going for 200 μs
10.3.6
(fc = 16 MHz)
in the internal clock. To start the timer, TC1CR<TC1S> specifies either the edge of the input pulse to the TC1
pin or the command start. TC1CR<MPPG1> specifies whether a duty pulse is produced continuously or not (one-
shot pulse).
negative pulse can be generated. Since the inverted level of the timer F/F1 output level is output to the PPG pin,
specify TC1CR<TFF1> to “0” to set the high level to the PPG pin, and “1” to set the low level to the PPG pin.
Upon reset, the timer F/F1 is initialized to “0”.
Note 1: To change TC1DRA or TC1DRB during a run of the timer, set a value sufficiently larger than the count value
Note 2: Do not change TC1CR<TFF1> during a run of the timer. TC1CR<TFF1> can be set correctly only at initial-
Note 3: In the PPG mode, the following relationship must be satisfied.
Note 4: Set TC1DRB after changing the mode of TC1M to the PPG mode.
In the programmable pulse generation (PPG) mode, an arbitrary duty pulse is generated by counting performed
Since the output level of the PPG pin can be set with TC1CR<TFF1> when the timer starts, a positive or
Programmable Pulse Generate (PPG) Output Mode
・ When TC1CR<MPPG1> is set to “0” (Continuous pulse generation)
・ When TC1CR<MPPG1> is set to “1” (One-shot pulse generation)
level of the PPG pin is inverted and an INTTC1 interrupt request is generated. The up-counter continues
counting. When a match between the up-counter and the TC1DRA value is detected, the level of the
PPG pin is inverted and an INTTC1 interrupt request is generated. The up-counter is cleared at this
time, and then continues counting and pulse generation.
the counter stops.
level of the PPG pin is inverted and an INTTC1 interrupt request is generated. The up-counter continues
counting. When a match between the up-counter and the TC1DRA value is detected, the level of the
PPG pin is inverted and an INTTC1 interrupt request is generated. TC1CR<TC1S> is cleared to “00”
automatically at this time, and the timer stops. The pulse generated by PPG retains the same level as
that when the timer stops.
of the counter. Setting a value smaller than the count value of the counter during a run of the timer may
generate a pulse different from that specified.
ization (after reset). When the timer stops during PPG, TC1CR<TFF1> can not be set correctly from this
point onward if the PPG output has the level which is inverted of the level when the timer starts. (Setting
TC1CR<TFF1> specifies the timer F/F1 to the level inverted of the programmed value.) Therefore, the timer
F/F1 needs to be initialized to ensure an arbitrary level of the PPG output. To initialize the timer F/F1, change
TC1CR<TC1M> to the timer mode (it is not required to start the timer mode), and then set the PPG mode.
Set TC1CR<TFF1> at this time.
TC1DRA > TC1DRB
When a match between the up-counter and the TC1DRB value is detected after the timer starts, the
When TC1S is cleared to “00” during PPG output, the PPG pin retains the level immediately before
When a match between the up-counter and the TC1DRB value is detected after the timer starts, the
LD
LDW
LDW
LD
Setting port
(TC1CR), 10000111B
(TC1DRA), 007DH
(TC1DRB), 0019H
(TC1CR), 10010111B
Page 95
; Sets the PPG mode, selects the source clock
; Sets the cycle (1 ms ÷ 2
; Sets the low-level pulse width (200 μs ÷ 2
; Starts the timer
7
/fc μs = 007DH)
7
/fc = 0019H)
TMP86FH92DMG