AT91SAM7XC512-CU Atmel, AT91SAM7XC512-CU Datasheet - Page 287

• Manufacturer Part Number: AT91SAM7XC512-CU
• Description: MCU ARM 512K HS FLASH 100-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7XC512-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 128 KB
• Interface Type: MII, SPI, TWI
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7X-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7XC-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7XC-EK - KIT EVAL FOR AT91SAM7XC256/128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Figure 29-7. Master Write with One Byte Internal Address and Multiple Data Bytes
29.6.4
287
TXCOMP
TXRDY
TWD
AT91SAM7XC512/256/128 Preliminary
Write THR (Data n)
Master Receiver Mode
S
DADR
The read sequence begins by setting the START bit. After the start condition has been sent, the
master sends a 7-bit slave address to notify the slave device. The bit following the slave address
indicates the transfer direction, 1 in this case (MREAD = 1 in TWI_MMR). During the acknowl-
edge clock pulse (9th pulse), the master releases the data line (HIGH), enabling the slave to pull
it down in order to generate the acknowledge. The master polls the data line during this clock
pulse and sets the NACK bit in the status register if the slave does not acknowledge the byte.
If an acknowledge is received, the master is then ready to receive data from the slave. After data
has been received, the master sends an acknowledge condition to notify the slave that the data
has been received except for the last data, after the stop condition. See
RXRDY bit is set in the status register, a character has been received in the receive-holding reg-
ister (TWI_RHR). The RXRDY bit is reset when reading the TWI_RHR.
When a single data byte read is performed, with or without internal address (IADR), the START
and STOP bits must be set at the same time. See
performed, with or without internal address (IADR), the STOP bit must be set after the next-to-
last data received. See
Figure 29-8. Master Read with One Data Byte
W
A
IADR(7:0)
TXCOMP
RXRDY
TWD
Figure
A
S
Write START &
29-9. For Internal Address usage see
DATA n
Write THR (Data n+1)
STOP Bit
DADR
A
R
Figure
A
Write THR (Data n+x)
DATA n+5
Last data sent
29-8. When a multiple data byte read is
DATA
A
Read RHR
Section
(ACK received and TXRDY = 1)
N
DATA n+x
STOP sent automaticaly
Figure
P
6209F–ATARM–17-Feb-09
29.6.5.
29-9. When the
A
P