AT91SAM7XC512-CU Atmel, AT91SAM7XC512-CU Datasheet - Page 286

• Manufacturer Part Number: AT91SAM7XC512-CU
• Description: MCU ARM 512K HS FLASH 100-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7XC512-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 128 KB
• Interface Type: MII, SPI, TWI
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7X-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7XC-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7XC-EK - KIT EVAL FOR AT91SAM7XC256/128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

29.6.3
Figure 29-6. Master Write with Multiple Data Byte
286
TXCOMP
TXRDY
TWD
AT91SAM7XC512/256/128 Preliminary
Master Transmitter Mode
Write THR (Data n)
S
DADR
The TWI Control Register (TWI_CR) allows configuration of the interface in Master Mode. In this
mode, it generates the clock according to the value programmed in the Clock Waveform Gener-
ator Register (TWI_CWGR). This register defines the TWCK signal completely, enabling the
interface to be adapted to a wide range of clocks.
After the master initiates a Start condition when writing into the Transmit Holding Register,
TWI_THR, it sends a 7-bit slave address, configured in the Master Mode register (DADR in
TWI_MMR), to notify the slave device. The bit following the slave address indicates the transfer
direction, 0 in this case (MREAD = 0 in TWI_MMR).
The TWI transfers require the slave to acknowledge each received byte. During the acknowl-
edge clock pulse (9th pulse), the master releases the data line (HIGH), enabling the slave to pull
it down in order to generate the acknowledge. The master polls the data line during this clock
pulse and sets the Not Acknowledge bit (NACK) in the status register if the slave does not
acknowledge the byte. As with the other status bits, an interrupt can be generated if enabled in
the interrupt enable register (TWI_IER). If the slave acknowledges the byte, the data written in
the TWI_THR, is then shifted in the internal shifter and transferred. When an acknowledge is
detected, the TXRDY bit is set until a new write in the TWI_THR. When no more data is written
into the TWI_THR, the master generates a stop condition to end the transfer. The end of the
complete transfer is marked by the TWI_TXCOMP bit set to one. See
and
Figure 29-5. Master Write with One Data Byte
• Master transmitter mode
• Master receiver mode
Figure
W
TXCOMP
TXRDY
TWD
29-7.
A
Write THR (DATA)
S
Write THR (Data n+1)
DATA n
DADR
A
W
A
Write THR (Data n+x)
DATA n+5
Last data sent
DATA
A
(ACK received and TXRDY = 1)
A
DATA n+x
STOP sent automaticaly
(ACK received and TXRDY = 1)
P
STOP sent automaticaly
Figure
6209F–ATARM–17-Feb-09
29-5,
A
Figure
P
29-6,