HD6432646 Hitachi, HD6432646 Datasheet - Page 744

no-image

HD6432646

Manufacturer Part Number
HD6432646
Description
(HD64F264x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HD6432646A52FCJ
Manufacturer:
RENESAS
Quantity:
1 000
Part Number:
HD6432646A52FCJ
Manufacturer:
HIT
Quantity:
1 000
Part Number:
HD6432646A52FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6432646B37FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6432646B67FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6432646B82FCJ
Manufacturer:
RENESAS
Quantity:
1 000
Part Number:
HD6432646B99FCJ
Manufacturer:
MOT
Quantity:
44
Part Number:
HD6432646B99FCJ
Manufacturer:
RENESAS
Quantity:
3 967
Part Number:
HD6432646B99FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6432646C41FCJ
Manufacturer:
RENESAS
Quantity:
1 954
Part Number:
HD6432646C41FCJ
Manufacturer:
RENESAS
Quantity:
1 700
Part Number:
HD6432646C41FCJ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6432646C64FCJ
Manufacturer:
RENESAS
Quantity:
1 500
Part Number:
HD6432646C90FCJV
Manufacturer:
RENESAS
Quantity:
3 967
Part Number:
HD6432646D08FCJV
Manufacturer:
RENESAS
Quantity:
1 700
20.13
Precautions concerning the use of on-board programming mode, the RAM emulation function, and
programmer mode are summarized below.
1. Use the specified voltages and timing for programming and erasing.
2. Powering on and off (see figures 20-26 to 20-28)
3. FWE application/disconnection (see figures 20-26 to 20-28)
710
Applied voltages in excess of the rating can permanently damage the device. Use a PROM
programmer that supports the Hitachi microcomputer device type with 128-kbyte on-chip flash
memory (FZTAT256V3A).
Do not select the HN27C4096 setting for the PROM programmer, and only use the specified
socket adapter. Failure to observe these points may result in damage to the device.
Do not apply a high level to the FWE pin until V
before turning off V
When applying or disconnecting V
in the hardware protection state.
The power-on and power-off timing requirements should also be satisfied in the event of a
power failure and subsequent recovery.
FWE application should be carried out when MCU operation is in a stable condition. If MCU
operation is not stable, fix the FWE pin low and set the protection state.
The following points must be observed concerning FWE application and disconnection to
prevent unintentional programming or erasing of flash memory:
Apply FWE when the V
Apply FWE when oscillation has stabilized (after the elapse of the oscillation settling
time).
In boot mode, apply and disconnect FWE during a reset.
In user program mode, FWE can be switched between high and low level regardless of a
reset state.
FWE input can also be switched during execution of a program in flash memory.
Do not apply FWE if program runaway has occurred.
Disconnect FWE only when the SWE, ESU, PSU, EV, PV, P, and E bits in FLMCR1 are
cleared.
Make sure that the SWE, ESU, PSU, EV, PV, P, and E bits are not set by mistake when
applying or disconnecting FWE.
Flash Memory Programming and Erasing Precautions
CC
.
CC
voltage has stabilized within its rated voltage range.
CC
power, fix the FWE pin low and place the flash memory
CC
has stabilized. Also, drive the FWE pin low

Related parts for HD6432646