LM3S101-CRN20-XNPP ETC1 [List of Unclassifed Manufacturers], LM3S101-CRN20-XNPP Datasheet - Page 82
![no-image](/images/no-image-200.jpg)
LM3S101-CRN20-XNPP
Manufacturer Part Number
LM3S101-CRN20-XNPP
Description
Microcontroller
Manufacturer
ETC1 [List of Unclassifed Manufacturers]
Datasheet
1.LM3S101-CRN20-XNPP.pdf
(284 pages)
- Current page: 82 of 284
- Download datasheet (3Mb)
7.2.2.3
7.3
7.3.1
7.3.2
March 22, 2006
Table 7-1.
An access that attempts to program or erase a PE-protected block is prohibited. A controller
interrupt may be optionally generated (by setting the AMASK bit in the FIM register) to alert
software developers of poorly behaving software during the development and debug phases.
An access that attempts to read an RE-protected block is prohibited. Such accesses return data
filled with all 0s. A controller interrupt may be optionally generated to alert software developers of
poorly behaving software during the development and debug phases.
The factory settings for the FMPRE and FMPPE registers are a value of 1 for all implemented
banks. This implements a policy of open access and programmability. The register bits may be
changed by writing the specific register bit. The changes are not permanent until the register is
committed (saved), at which point the bit change is permanent. If a bit is changed from a 1 to a 0
and not committed, it may be restored by executing a power-on reset sequence.
Flash Memory Programming
Writing the flash memory requires that the code be executed out of SRAM to avoid corrupting or
interrupting the bus timing. Flash pages can be erased on a page basis (1 KB in size), or by
performing a mass erase of the entire flash.
All erase and program operations are performed using the Flash Memory Address (FMA), Flash
Memory Data (FMD) and Flash Memory Control (FMC) registers. See section 7.3 for examples.
Initialization and Configuration
This section shows examples for using the flash controller to perform various operations on the
contents of the flash memory.
Changing Flash Protection Bits
As discussed in Section 7.2.2.2, changes to the protection bits must be committed before they
take effect. The sequence to change and commit a bit in software is as follows:
1.
2.
3.
Flash Programming
The Stellaris devices provide a user-friendly interface for flash programming. All erase/program
operations are handled via three registers: FMA, FMD and FMC.
FMPPE
The Flash Memory Protection Read Enable (FMPRE) and Flash Memory Protection Pro-
gram Enable (FMPPE) registers are written, changing the intended bit(s). The action of these
changes can be tested by software while in this state.
The Flash Memory Address (FMA) register (see page 86) bit 0 is set to 1 if the FMPPE reg-
ister is to be committed; otherwise, a 0 commits the FMPRE register.
The Flash Memory Control (FMC) register (see page 88) is written with the COMT bit set. This
initiates a write sequence and commits the changes.
0
1
Flash Protection Policy Combinations
FMPRE
1
1
Protection
Read-only protection. The block may be read or executed but may not be
written or erased. This mode is used to lock the block from further modification
while allowing any read or execute access.
No protection. The block may be written, erased, executed or read.
Preliminary
LM3S101 Data Sheet
82
Related parts for LM3S101-CRN20-XNPP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LM3S101](/images/no-image3.png)
Part Number:
Description:
Microcontroller
Manufacturer:
Luminary Micro, Inc.
Datasheet:
![LM3S101-CRN20-XNPT](/images/no-image3.png)
Part Number:
Description:
Microcontroller
Manufacturer:
Luminary Micro, Inc.
Datasheet:
![LM3S101-IRN20](/images/no-image3.png)
Part Number:
Description:
Microcontroller
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
![TC2411-IB](/images/no-image3.png)
Part Number:
Description:
14-Bit, 1 GSPS Digital-to-Analog Converter with Standby Mode of Operation
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![S2010GE10PL](/images/no-image3.png)
Part Number:
Description:
A SERIES OF SPECTRAL - RESPONSE SILICON PHOTOCELLS DESIGNED FOR UNIQUE PRODUCT APPLICATIONS
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![GT620NS](/images/no-image3.png)
Part Number:
Description:
Mini size of Discrete semiconductor elements
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![PMKC03-05D05](/images/no-image3.png)
Part Number:
Description:
3 Watts of Output Power From a Package
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![S2559E](/images/no-image3.png)
Part Number:
Description:
DTMF Tone Generator
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![TIC216M](/images/no-image3.png)
Part Number:
Description:
SILICON TRIACS
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![P2503NVG](/images/no-image3.png)
Part Number:
Description:
N P-Channel Enhancement Mode Enhancement Mode
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![NT3883F](/images/no-image3.png)
Part Number:
Description:
Dot Matrix LCD 80-Channel Driver
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![PCA9512AD](/images/no-image3.png)
Part Number:
Description:
Level shifting hot swappable I2C-bus and SMBus bus buffer
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![TCM2010-101-4P](/images/no-image3.png)
Part Number:
Description:
Common Mode Choke Coils for Signal Line SMD
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![U4085B](/images/no-image3.png)
Part Number:
Description:
Technische Daten Technical Data
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet:
![AT1730P](/images/no-image3.png)
Part Number:
Description:
2-Channel PWM Controller for LCD Bias
Manufacturer:
ETC1 [List of Unclassifed Manufacturers]
Datasheet: