ATxmega64A4U Atmel Corporation, ATxmega64A4U Datasheet - Page 191
ATxmega64A4U
Manufacturer Part Number
ATxmega64A4U
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega64A4U
Flash (kbytes)
64 Kbytes
Pin Count
44
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
34
Ext Interrupts
34
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
2
Uart
5
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
2
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
AES/DES
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
5
Output Compare Channels
16
Input Capture Channels
16
Pwm Channels
16
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega64A4U-AU
Manufacturer:
ON
Quantity:
29 000
Company:
Part Number:
ATxmega64A4U-U
Manufacturer:
ATMEL
Quantity:
74
- Current page: 191 of 505
- Download datasheet (8Mb)
15.5
15.5.1
8331A–AVR–07/11
Counter Operation
Changing the Period
Figure 15-2. Clock Selection
The Peripheral Clock (clk
in a device). A selection of the prescaler outputs from 1 to 1/2024 is directly available. In addition
the whole range from 1 to 2
The clock selection (CLKSEL) selects one of the clock prescaler outputs or an event channel for
the High Byte Counter (CNTH) and Low Byte Counter (CNTL). By using the Event System, any
event source such as an external clock signal on any I/O pin can be used as clock input.
By default no clock input is selected and the Counters are not running.
The Counters will always count in single slope mode. Each Counter counts down for each clock
cycle until it reaches BOTTOM, and then reloads the Counter with the Period Register value at
the following clok cycle.
Figure 15-3. Counter Operation
As shown in
access has higher priority than count, and reloads and will be immediate.
The Counter period is changed by writing a new TOP value to the Period Register. Since the
Counter is counting down, the Period Register can be written at any time without affecting the
current period as shown in
of odd waveforms.
CNT
clk
PER
CLKSEL
BOTTOM
Figure
MAX
TOP
Prescaler
Common
15-3, the counter can change the counter value while running. The write
{0,1,2,4,8,64,256,1024}
PER
Figure 15-4 on page
15
) is fed into the Common Prescaler (common for all Timer/Counters
time prescalings is available through the Event System.
clk
PER
/
clk
2
{0,...,15}
PER
/
CNT written
192. This prevents wraparound and generation
Event System
event channels
Atmel AVR XMEGA AU
CNT
events
"reload"
191
Related parts for ATxmega64A4U
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: