CYRF69213-40LFXC Cypress Semiconductor Corp, CYRF69213-40LFXC Datasheet - Page 7

• Manufacturer Part Number: CYRF69213-40LFXC
• Description: IC PROC 8K FLASH 40VQFN
• Manufacturer: Cypress Semiconductor Corp
• Series: CYRFr
• Type: Transceiverr

Specifications of CYRF69213-40LFXC

• Package / Case: 40-VQFN Exposed Pad, 40-HVQFN, 40-SQFN, 40-DHVQFN
• Frequency: 2.4GHz
• Data Rate - Maximum: 1Mbps
• Modulation Or Protocol: ISM
• Applications: General Purpose
• Power - Output: 4dBm
• Sensitivity: -97dBm
• Voltage - Supply: 4 V ~ 5.5 V
• Current - Receiving: 23.4mA
• Current - Transmitting: 36.6mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 256B SRAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: 0°C ~ 70°C
• Operating Frequency: 2497 MHz
• Operating Supply Voltage: 2.5 V or 3.3 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Temperature (min): 0C
• Operating Temperature (max): 70C
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1001 - ISP 4PORT CYPRESS ENCORE II MCU
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-1934

Packet Buffers
Packet data and configuration registers are accessed through
the SPI interface. All configuration registers are directly
addressed through the address field in the SPI packet. Configu-
ration registers are provided to allow configuration of DSSS PN
codes, data rate, operating mode, interrupt masks, interrupt
status, and others.
Packet Buffers
All data transmission and reception uses the 16-byte packet
buffers—one for transmission and one for reception.
The transmit buffer allows a complete packet of up to 16 bytes of
payload data to be loaded in one burst SPI transaction,.This is
then transmitted with no further MCU intervention. Similarly, the
receive buffer allows an entire packet of payload data up to 16
bytes to be received with no firmware intervention required until
packet reception is complete.
The CYRF69213 IC supports packet length of up to 40 bytes;
interrupts are provided to allow an MCU to use the transmit and
receive buffers as FIFOs. When transmitting a packet longer
than 16 bytes, the MCU can load 16 bytes initially, and add
further bytes to the transmit buffer as transmission of data
creates space in the buffer. Similarly, when receiving packets
longer than 16 bytes, the MCU function must fetch received data
from the FIFO periodically during packet reception to prevent it
from overflowing.
Auto Transaction Sequencer (ATS)
The CYRF69213 IC provides automated support for trans-
mission and reception of acknowledged data packets.
When transmitting a data packet, the device automatically starts
the crystal and synthesizer, enters transmit mode, transmits the
packet in the transmit buffer, and then automatically switches to
receive mode and waits for a handshake packet—and then
automatically reverts to sleep mode or idle mode when either an
ACK packet is received, or a timeout period expires.
Similarly, when receiving in transaction mode, the device waits
in receive mode for a valid packet to be received, then automat-
ically transitions to transmit mode, transmits an ACK packet, and
then switches back to receive mode to await the next packet. The
contents of the packet buffers are not affected by the trans-
mission or reception of ACK packets.
In each case, the entire packet transaction takes place without
any need for MCU firmware action; to transmit data the MCU
simply needs to load the data packet to be transmitted, set the
length, and set the TX GO bit. Similarly, when receiving packets
in transaction mode, firmware simply needs to retrieve the fully
Document #: 001-07552 Rev. *D
P re a m b le
n x 1 6 u s
P
1 s t F ra m in g
S O P 1
S y m b o l*
2 n d F ra m in g
S y m b o l*
S O P 2
Figure 2. Example Default Packet Format
L e n g t h
P a c k e t
P e rio d
le n g th
1 B y te
P a y lo a d D a t a
received packet in response to an interrupt request indicating
reception of a packet.
Interrupts
The radio function provides an interrupt (IRQ) output, which is
configurable to indicate the occurrence of various different
events. The IRQ pin may be programmed to be either active high
or active low, and be either a CMOS or open drain output. The
IRQ pin can be multiplexed on the SPI if routed to an external pin.
The radio function features three sets of interrupts: transmit,
receive, and system interrupts. These interrupts all share a
single pin (IRQ), but can be independently enabled/disabled. In
transmit mode, all receive interrupts are automatically disabled,
and in receive mode all transmit interrupts are automatically
disabled. However, the contents of the enable registers are
preserved when switching between transmit and receive modes.
If more than one radio interrupt is enabled at any time, it is
necessary to read the relevant status register to determine which
event caused the IRQ pin to assert. Even when a given interrupt
source is disabled, the status of the condition that would
otherwise cause an interrupt can be determined by reading the
appropriate status register. It is therefore possible to use the
devices without making use of the IRQ pin by polling the status
register(s) to wait for an event, rather than using the IRQ pin.
The microcontroller function supports 23 maskable interrupts in
the vectored interrupt controller. Interrupt sources include a USB
bus reset, LVR/POR, a programmable interval timer, a 1.024-ms
output from the Free Running Timer, three USB endpoints, two
capture timers, five GPIO Ports, three GPIO pins, two SPI, a
16-bit free running timer wrap, an internal wakeup timer, and a
bus active interrupt. The wakeup timer causes periodic interrupts
when enabled. The USB endpoints interrupt after a USB trans-
action complete is on the bus. The capture timers interrupt
whenever a new timer value is saved due to a selected GPIO
edge event. A total of eight GPIO interrupts support both TTL or
CMOS thresholds. For additional flexibility, on the edge sensitive
GPIO pins, the interrupt polarity is programmable to be either
rising or falling.
Clocks
The radio function has a 12 MHz crystal (30-ppm or better)
directly connected between XTAL and GND without the need for
external capacitors. A digital clock out function is provided, with
selectable output frequencies of 0.75, 1.5, 3, 6, or 12 MHz. This
output may be used to clock an external microcontroller (MCU)
or ASIC. This output is enabled by default, but may be disabled.
* N o te :3 2 o r 6 4 u s
CYRF69213
C R C 1 6
Page 7 of 77
[+] Feedback