CYRF69213-40LFXC Cypress Semiconductor Corp, CYRF69213-40LFXC Datasheet - Page 60

• Manufacturer Part Number: CYRF69213-40LFXC
• Description: IC PROC 8K FLASH 40VQFN
• Manufacturer: Cypress Semiconductor Corp
• Series: CYRFr
• Type: Transceiverr

Specifications of CYRF69213-40LFXC

• Package / Case: 40-VQFN Exposed Pad, 40-HVQFN, 40-SQFN, 40-DHVQFN
• Frequency: 2.4GHz
• Data Rate - Maximum: 1Mbps
• Modulation Or Protocol: ISM
• Applications: General Purpose
• Power - Output: 4dBm
• Sensitivity: -97dBm
• Voltage - Supply: 4 V ~ 5.5 V
• Current - Receiving: 23.4mA
• Current - Transmitting: 36.6mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 256B SRAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: 0°C ~ 70°C
• Operating Frequency: 2497 MHz
• Operating Supply Voltage: 2.5 V or 3.3 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Temperature (min): 0C
• Operating Temperature (max): 70C
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1001 - ISP 4PORT CYPRESS ENCORE II MCU
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-1934

USB Mode Tables
Mode Column
The 'Mode' column contains the mnemonic names given to the
modes of the endpoint. The mode of the endpoint is determined
by the four-bit binaries in the 'Encoding' column as discussed in
the following section. The Status IN and Status OUT represent
the status IN or OUT stage of the control transfer.
Encoding Column
The contents of the 'Encoding' column represent the Mode
Bits [3:0] of the Endpoint Mode Registers
Table
to different tokens that the host sends to the endpoints. For
example, if the Mode Bits [3:0] of the Endpoint 0 Mode Register
are set to '0001', which is NAK IN/OUT mode, the SIE sends an
ACK handshake in response to SETUP tokens and NAK any IN
or OUT tokens.
Document #: 001-07552 Rev. *D
ACK OUT (STALL =
ACK OUT (STALL =
ACK IN (STALL = 0)
ACK IN (STALL = 1)
STATUS IN ONLY
STALL IN/OUT
STATUS OUT
STATUS OUT
NAK IN/OUT
ACK OUT –
STATUS IN
NAK OUT
DISABLE
ACK IN –
Reserved
Reserved
Reserved
Reserved
Reserved
83). The endpoint modes determine how the SIE responds
NAK IN
Mode
ONLY
0)
1)
Encoding
0000
0001
0010
0011
0110
1011
1000
1001
1001
1100
1101
1101
0101
1010
0100
1111
0111
1110
SETUP
Accept
Accept
Accept
Accept
Accept
Accept
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
TX Count
TX Count
TX0 byte
TX0 byte
STALL
STALL
STALL
(Table 82
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
NAK
NAK
IN
and
STALL
STALL
STALL
Ignore
Check
Check
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
OUT
NAK
ACK
NAK
ACK
SETUP, IN, and OUT Columns
Depending on the mode specified in the 'Encoding' column, the
'SETUP', 'IN', and 'OUT' columns contain the SIE's responses
when the endpoint receives SETUP, IN, and OUT tokens,
respectively.
A 'Check' in the Out column means that upon receiving an OUT
token the SIE checks to see whether the OUT is of zero length
and has a Data Toggle (Data1/0) of 1. If these conditions are true,
the SIE responds with an ACK. If any of the above conditions is
not met, the SIE responds with either a STALL or Ignore.
A 'TX Count' entry in the IN column means that the SIE transmits
the number of bytes specified in the Byte Count Bit [3:0] of the
Endpoint Count Register
STALL the IN transfer. Data endpoint only
Ignore all USB traffic to this endpoint. Used by Data and
Control endpoints
NAK IN and OUT token. Control endpoint only
STALL IN and ACK zero byte OUT. Control endpoint only
STALL IN and OUT token. Control endpoint only
STALL OUT and send zero byte data for IN token. Control
endpoint only
ACK the OUT token or send zero byte data for IN token.
Control endpoint only
Respond to IN data or Status OUT. Control endpoint only
Send NAK handshake to OUT token. Data endpoint only
This mode is changed by the SIE to mode 1000 on issu-
ance of ACK handshake to an OUT. Data endpoint only
STALL the OUT transfer
Send NAK handshake for IN token. Data endpoint only
This mode is changed by the SIE to mode 1100 after re-
ceiving ACK handshake to an IN data. Data endpoint only
These modes are not supported by SIE. Firmware should
not use this mode in Control and Data endpoints
Comments
(Table
81) in response to any IN token.
CYRF69213
Page 60 of 77
[+] Feedback