CYRF69213-40LFXC Cypress Semiconductor Corp, CYRF69213-40LFXC Datasheet - Page 56

• Manufacturer Part Number: CYRF69213-40LFXC
• Description: IC PROC 8K FLASH 40VQFN
• Manufacturer: Cypress Semiconductor Corp
• Series: CYRFr
• Type: Transceiverr

Specifications of CYRF69213-40LFXC

• Package / Case: 40-VQFN Exposed Pad, 40-HVQFN, 40-SQFN, 40-DHVQFN
• Frequency: 2.4GHz
• Data Rate - Maximum: 1Mbps
• Modulation Or Protocol: ISM
• Applications: General Purpose
• Power - Output: 4dBm
• Sensitivity: -97dBm
• Voltage - Supply: 4 V ~ 5.5 V
• Current - Receiving: 23.4mA
• Current - Transmitting: 36.6mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 256B SRAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: 0°C ~ 70°C
• Operating Frequency: 2497 MHz
• Operating Supply Voltage: 2.5 V or 3.3 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Temperature (min): 0C
• Operating Temperature (max): 70C
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1001 - ISP 4PORT CYPRESS ENCORE II MCU
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-1934

Table 81. Endpoint 0, 1, and 2 Count (EP0CNT–EP2CNT) [0x41, 0x43, 0x45] [R/W]
Document #: 001-07552 Rev. *D
Bit #
Field
Read/Write
Default
Bit 7
Bit 6
Bits 5:4
Bits 3:0
For Endpoint 0 Count Register, whenever the count updates from a SETUP or OUT transaction, the count register locks and cannot
be written by the CPU. Reading the register unlocks it. This prevents firmware from overwriting a status update on it
Data Toggle
This bit selects the DATA packet's toggle state. For IN transactions, firmware must set this bit to the select the trans-
mitted Data Toggle. For OUT or SETUP transactions, the hardware sets this bit to the state of the received Data Tog-
gle bit.
0 = DATA0
1 = DATA1
Data Valid
This bit is used for OUT and SETUP tokens only. This bit is cleared to ‘0’ if CRC, bitstuff, or PID errors have occurred.
This bit does not update for some endpoint mode settings
0 = Data is invalid. If enabled, the endpoint interrupt occurs even if invalid data is received
1 = Data is valid
Reserved
Byte Count Bit [3:0]
Byte Count Bits indicate the number of data bytes in a transaction: For IN transactions, firmware loads the count with the
number of bytes to be transmitted to the host from the endpoint FIFO. Valid values are 0 to 8 inclusive. For OUT or
SETUP transactions, the count is updated by hardware to the number of data bytes received, plus 2 for the CRC bytes.
Valid values are 2–10 inclusive.
Data Toggle
R/W
7
0
Data Valid
R/W
6
0
R/W
5
0
Reserved
R/W
4
0
R/W
3
0
R/W
2
0
Byte Count[3:0]
R/W
1
0
CYRF69213
Page 56 of 77
R/W
0
0
[+] Feedback