ATMEGA168-15AZ Atmel, ATMEGA168-15AZ Datasheet - Page 299

MCU AVR 16K FLASH 15MHZ 32-TQFP

ATMEGA168-15AZ

Manufacturer Part Number
ATMEGA168-15AZ
Description
MCU AVR 16K FLASH 15MHZ 32-TQFP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet

Specifications of ATMEGA168-15AZ

Package / Case
32-TQFP, 32-VQFP
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Speed
16MHz
Number Of I /o
23
Eeprom Size
512 x 8
Core Processor
AVR
Program Memory Type
FLASH
Ram Size
1K x 8
Program Memory Size
16KB (16K x 8)
Data Converters
A/D 8x10b
Oscillator Type
Internal
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Connectivity
I²C, SPI, UART/USART
Core Size
8-Bit
Cpu Family
ATmega
Device Core
AVR
Device Core Size
8b
Frequency (max)
16MHz
Interface Type
2-Wire/USART/Serial
Total Internal Ram Size
1KB
# I/os (max)
23
Number Of Timers - General Purpose
3
Operating Supply Voltage (typ)
3.3/5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
2.7V
On-chip Adc
8-chx10-bit
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 125C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Pin Count
32
Package Type
TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA168-15AZ
Manufacturer:
Atmel
Quantity:
10 000
T
Notes:
7530I–AVR–02/10
A
Symbol
I
V
I
t
CC
ACLK
ACID
ACIO
= -40°C to 125°C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at V
4. Although each I/O port can source more than the test conditions (20mA at V
conditions (non-transient), the following must be observed:
ATmega48:
1] The sum of all IOL, for ports C0 - C5, should not exceed 70 mA.
2] The sum of all IOL, for ports C6, D0 - D4, should not exceed 70 mA.
3] The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 70 mA.
ATmega88/168:
1] The sum of all IOL, for ports C0 - C5, should not exceed 100 mA.
2] The sum of all IOL, for ports C6, D0 - D4, should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
ATmega48:
1] The sum of all IOH, for ports C0 - C5, should not exceed 70 mA.
2] The sum of all IOH, for ports C6, D0 - D4, should not exceed 70 mA.
3] The sum of all IOH, for ports B0 - B7, D5 - D7, should not exceed 70 mA.
ATmega88/168:
1] The sum of all IOH, for ports C0 - C5, should not exceed 100 mA.
2] The sum of all IOH, for ports C6, D0 - D4, should not exceed 100 mA.
3] The sum of all IOH, for ports B0 - B7, D5 - D7, should not exceed 100 mA.
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
= 2.7V to 5.5V (unless otherwise noted)
(6)
Active 4MHz, V
(ATmega48/88/168L)
Active 8MHz, V
(ATmega48/88/168)
Active 15MHz, V
(ATmega48/88/168)
Idle 4MHz, V
(ATmega48/88/168V)
Idle 8MHz, V
(ATmega48/88/168L)
Idle 15MHz, V
(ATmega48/88/168)
WDT enabled, V
WDT enabled, V
WDT disabled, V
WDT disabled, V
V
V
V
V
V
Condition
CC
in
CC
in
CC
= V
= V
= 5V
= 5V
= 4.5V
CC
CC
/2
/2
CC
CC
CC
CC
CC
= 3V
= 5V
CC
CC
CC
CC
CC
= 5V
= 3V
= 5V
= 3V
= 5V
= 5V
= 3V
= 5V
ATmega48/88/168 Automotive
Min.
-50
(5)
CC
CC
= 5V, 10mA at V
= 5V, 10mA at V
Typ.
10.0
12.6
140
1.8
6.0
0.4
1.4
2.8
6.6
10
8
5
CC
Max.
CC
= 3V) under steady state
3.0
2.4
10
16
30
50
24
36
40
50
1
4
= 3V) under steady state
(5)
Units
mA
mA
mA
mA
mA
mA
mV
µA
µA
µA
µA
nA
ns
299

Related parts for ATMEGA168-15AZ