ATtiny5 Atmel Corporation, ATtiny5 Datasheet - Page 9

• Manufacturer Part Number: ATtiny5
• Manufacturer: Atmel Corporation

Specifications of ATtiny5

• Flash (kbytes): 0.5 Kbytes
• Pin Count: 6
• Max. Operating Frequency: 12 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 1
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 4
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 8
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.03
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 2
• Input Capture Channels: 1
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

4.5
4.6
8127E–AVR–11/11
Stack Pointer
Instruction Execution Timing
Figure 4-3.
In different addressing modes these address registers function as automatic increment and
automatic decrement (see document “AVR Instruction Set” and section
mary” on page 152
The Stack is mainly used for storing temporary data, for storing local variables and for storing
return addresses after interrupts and subroutine calls. The Stack Pointer Register always points
to the top of the Stack. Note that the Stack is implemented as growing from higher memory loca-
tions to lower memory locations. This implies that a Stack PUSH command decreases the Stack
Pointer.
The Stack Pointer points to the data SRAM Stack area where the Subroutine and Interrupt
Stacks are located. This Stack space in the data SRAM must be defined by the program before
any subroutine calls are executed or interrupts are enabled. The Stack Pointer must be set to
point above 0x40. The Stack Pointer is decremented by one when data is pushed onto the Stack
with the PUSH instruction, and it is decremented by two when the return address is pushed onto
the Stack with subroutine call or interrupt. The Stack Pointer is incremented by one when data is
popped from the Stack with the POP instruction, and it is incremented by two when data is
popped from the Stack with return from subroutine RET or return from interrupt RETI.
The AVR Stack Pointer is implemented as two 8-bit registers in the I/O space. The number of
bits actually used is implementation dependent. Note that the data space in some implementa-
tions of the AVR architecture is so small that only SPL is needed. In this case, the SPH Register
will not be present.
This section describes the general access timing concepts for instruction execution. The AVR
CPU is driven by the CPU clock clk
chip. No internal clock division is used.
X-register
Y-register
Z-register
The X-, Y-, and Z-registers
for details).
15
7
15
7
15
7
CPU
R27
R29
R31
XH
YH
ZH
, directly generated from the selected clock source for the
0
0
0
7
7
7
ATtiny4/5/9/10
“Instruction Set Sum-
XL
YL
ZL
R26
R28
R30
0
0
0
0
0
0
9