UPD784026 Renesas Electronics Corporation., UPD784026 Datasheet - Page 400
UPD784026
Manufacturer Part Number
UPD784026
Description
16/8-bit Single-chip Microcontrollers
Manufacturer
Renesas Electronics Corporation.
Datasheet
1.UPD784026.pdf
(759 pages)
- Current page: 400 of 759
- Download datasheet (3Mb)
12.2 WATCHDOG TIMER MODE REGISTER (WDM)
a dedicated instruction. This dedicated instruction, MOV WDM,#byte, has a special code configuration (4 bytes), and a
write is not performed unless the 3rd and 4th bytes of the operation code are mutual complements.
is generated. In this case, the return address saved in the stack area is the address of the instruction that was the source
of the error, and thus the address that was the source of the error can be identified from the return address saved in the
stack area.
RA78K/IV, only the correct dedicated instruction is generated when MOV WDM, #byte is written), system initialization should
be performed by the program.
operation. That is, a write is not performed to the WDM, and an interrupt such as an operand error interrupt is not generated.
contents cannot be changed. The watchdog timer can only be stopped by a reset, but can be cleared at any time with a
dedicated instruction.
360
The WDM is an 8-bit register that controls the watchdog timer operation.
To prevent erroneous clearing of the watchdog timer by an inadvertent program loop, writing can only be performed by
If the 3rd and 4th bytes of the operation code are not complements, a write is not performed and an operand error interrupt
If recovery from an operand error is simply performed by means of an RETB instruction, an endless loop will result.
As an operand error interrupt is only generated in the event of an inadvertent program loop (with the NEC assembler,
Other write instructions (MOV WDM, A; AND WDM, #byte; SET1 WDM.7, etc.) are ignored and do not perform any
After a system reset (RESET input), once the watchdog timer has been started (by setting (1) the RUN bit), the WDM
The WDM can be read at any time by a data transfer instruction.
RESET input clears the WDM to 00H.
The WDM format is shown in Figure 12-2.
CHAPTER 12 WATCHDOG TIMER FUNCTION
Related parts for UPD784026
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Renesas Technology Corp [Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series]
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
RENESAS MCU M16C FAMILY / M16C/Tiny SERIES
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas Starter Kit for RX210
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas StarterKit for RX630
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit+ for RX63N
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
FLASH PROGRAMMER FOR RENESAS MICROCONTROLLERS
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet: