TMPM364F10FG Toshiba, TMPM364F10FG Datasheet - Page 772

• Manufacturer Part Number: TMPM364F10FG
• Manufacturer: Toshiba

Specifications of TMPM364F10FG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 144
• Package: LQFP(20x20)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 5
• Uart/sio (ch): 12
• Usb: Host
• Can: 1
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: 16
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: Y
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit

24.2
Operation Mode
4. The 5th to 8th bytes, transmitted from the target board to the controller, are the data read from
5. The 9th to 20th bytes, transmitted from the target board to the controller, indicate the product
6. The 21st to 24th bytes, transmitted from the target board to the controller, indicate the start ad-
7. The 25th to 28th bytes, transmitted from the target board to the controller, indicate the start ad-
8. The 29th to 32nd bytes, transmitted from the target board to the controller, are dummy data. Start-
9. The 33rd to 36th bytes, transmitted from the target board to the controller, indicate the end ad-
the command wait state again. In this case, the upper four bits of the acknowledge response
are undefined- they hold the same values as the upper four bits of the previously issued com-
mand. When the SIO4 is configured for I/O Interface mode, the boot program does not check
for a receive error.
echoes it back to the controller. When the Show Flash Memory Sum command is received,
the boot program echoes back a value of 0x30 and then branches to the Show Flash Memory
Sum routine. If the 3rd byte is not a valid command, the boot program sends back 0xX1 (bit
0) to the controller and returns to the state in which it waits for a command (the third byte)
again. In this case, the upper four bits of the acknowledge response are undefined - they hold
the same values as the upper four bits of the previously issued command.
addresses shown below in the flash memory. Software version management is possible by stor-
ing a software ID in these locations.
name as shown below (where [ ] is a space) in ASCII code.
dress of the flash memory area contained the password. Each product has own start address
shown below. Starting from the 21st byte, the following values are transmitted.
dress of the on-chip RAM. TMPM364F10FG has own start address shown below. Starting
from the 25th byte, the following values are transmitted.
ing from the 29th byte, 0x00, 0x00, 0x00, 0x00 are transmitted.
dress of the on-chip RAM. TMPM364F10FG has own end address shown below. Starting
from the 33th byte, the following values are transmitted.
If the 3rd byte is equal to any of the command codes listed in Table 24-4, the boot program
TMPM364F10FG
TMPM364F10FG
TMPM364F10FG
TMPM364F10FG
TMPM364F10FG
Product name
Product name
Product name
Product name
Product name
Page 746
T, M, P, M, 3, 6, 0, F, 1, _, [ ], _
0x3F8F_FFF0 to 0x3F8F_FFF3
0xFF, 0xFF, 0x00, 0x20
0xF4, 0xFF,0x8F, 0x3F
0x00, 0x00,0x00, 0x20
Address
Address
Address
Core
Area
TMPM364F10FG