TMPM364F10FG Toshiba, TMPM364F10FG Datasheet - Page 41

• Manufacturer Part Number: TMPM364F10FG
• Manufacturer: Toshiba

Specifications of TMPM364F10FG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 144
• Package: LQFP(20x20)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 5
• Uart/sio (ch): 12
• Usb: Host
• Can: 1
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: 16
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: Y
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit

Table 1-1 Pin Names and Functions Sorted by Pin (9/10)
Function
Function
Function
Function
Function
Function
Function
Function
Function
Control
Clock
Clock
Clock
Clock
TEST
TEST
Type
PS
PS
PS
PS
PS
PS
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
Pin
No.
PH6
SCK4
TBEIN0
PH7
INTD
TBEIN1
RVDD3
XT1
XT2
DVDD3A
X1
DVSS
X2
DVDD3B
DVSS
D+
D-
NMI
TEST1
TEST2
PI0
BOOT
PI1
CEC
AVDD3
PJ0
AIN0
PJ1
AIN1
PJ2
AIN2
PIn Name
I/O
I/O
Input
I/O
Input
Input
-
Input
Output
-
Input
-
Output
-
-
I/O
I/O
Input
-
-
I/O
Input
I/O
I/O
-
Input
Input
Input
Input
Input
Input
Output
Input /
I/O port
Inputting and outputting a clock if the serial bus interface operates in the SIO mode.
Inputting the Timer B capture trigger
I/O port
External interrupt pin
Inputting the Timer B capture trigger
Power supply pin
Connected to a low-speed oscillator.
Connected to a low-speed oscillator.
Power supply pin
Connected to a high-speed oscillator.
GND pin
Connected to a high-speed oscillator.
Power supply pin
GND pin
USB data pulse
USB data minus
Non-maskable interrupt
(note) With a noise filter (about 30ns (typical value))
TEST pin
(note) TEST pin must be left OPEN.
TEST pin
(note) TEST pin must be left OPEN.
I/O port
BOOT pin
(note) This pin goes into single boot mode by sampling "Low" at the rise of a RESET signal.
I/O port
CEC pin
(note) Nch open drain port
Supplying the AD converter with a power supply.
(note) AVDD3 must be connected to power supply even if A/D converter is not used.
Input port
Analog input
Input port
Analog input
Input port
Analog input
Page 15
Function
TMPM364F10FG