ATA6613P-PLQW Atmel, ATA6613P-PLQW Datasheet - Page 7

• Manufacturer Part Number: ATA6613P-PLQW
• Description: MCU W/LIN TXRX REG WTCHDG 48-QFN
• Manufacturer: Atmel
• Series: AVR® ATA66 LIN-SBCr

Specifications of ATA6613P-PLQW

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: ATA6x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
9111H–AUTO–01/11
Functional Description
Physical Layer Compatibility
Supply Pin (VS)
Ground Pin (GND)
Voltage Regulator Output Pin (VCC)
Voltage Regulator Sense Pin (PVCC)
Bus Pin (LIN)
Since the LIN physical layer is independent from higher LIN layers (e.g., the LIN protocol
layer), all nodes with a LIN physical layer according to revision 2.x can be mixed with LIN
physical layer nodes, which, according to older versions (i.e., LIN 1.0, LIN 1.1, LIN 1.2, LIN
1.3), are without any restrictions.
The LIN operating voltage is V
able data transmission if V
switching on VS, the IC starts in Fail-safe Mode, and the voltage regulator is switched on (i.e.,
output capability).
The supply current is typically 10µA in Sleep Mode and 57µA in Silent Mode.
The IC does not affect the LIN Bus in the event of GND disconnection. It is able to handle a
ground shift up to 11.5% of VS. The mandatory system ground is pin 5.
The internal voltage regulator is capable of driving loads with up to 50mA. It is able to supply
the microcontroller and other ICs on the PCB and is protected against overloads by means of
current limitation and overtemperature shut-down. Furthermore, the output voltage is moni-
tored and will cause a reset signal at the NRES output pin if it drops below a defined threshold
V
base connected to the VCC pin and its emitter connected to PVCC.
The PVCC is the sense input pin of the voltage regulator. For normal applications (i.e., when
only using the internal output transistor), this pin is connected to the VCC pin. If an external
boosting transistor is used, the PVCC pin must be connected to the output of this transistor,
i.e., its emitter terminal.
A low-side driver with internal current limitation and thermal shutdown and an internal pull-up
resistor compliant with the LIN 2.x specification are implemented. The allowed voltage range
is between –27V and +40V. Reverse currents from the LIN bus to VS are suppressed, even in
the event of GND shifts or battery disconnection. LIN receiver thresholds are compatible with
the LIN protocol specification. The fall time from recessive to dominant bus state and the rise
time from dominant to recessive bus state are slope controlled.
thun
. To boost up the maximum load current, an external NPN transistor may be used, with its
S
falls below VS
S
= 5V to 27V. An undervoltage detection is implemented to dis-
th
< 4V in order to avoid false bus messages. After
Atmel ATA6612/ATA6613
7