ATA6613P-PLQW Atmel, ATA6613P-PLQW Datasheet - Page 318

• Manufacturer Part Number: ATA6613P-PLQW
• Description: MCU W/LIN TXRX REG WTCHDG 48-QFN
• Manufacturer: Atmel
• Series: AVR® ATA66 LIN-SBCr

Specifications of ATA6613P-PLQW

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: ATA6x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 6-127. Serial Programming Waveforms
Table 6-128. Serial Programming Instruction Set
318
Instruction
Programming Enable
Chip Erase
Read Program Memory
Load Program Memory Page
Write Program Memory Page
Read EEPROM Memory
Write EEPROM Memory
Load EEPROM Memory Page
(page access)
Write EEPROM Memory Page
(page access)
Atmel ATA6612/ATA6613
SERIAL DATA OUTPUT
SERIAL CLOCK INPUT
SERIAL DATA INPUT
SAMPLE
(MOSI)
(MISO)
(SCK)
In this case, data polling cannot be used for the value 0xFF, and the user will have to wait at
least t
t
Table 6-127. Minimum Wait Delay Before Writing the Next Flash or EEPROM Location
Symbol
t
t
t
WD_EEPROM
WD_FLASH
WD_EEPROM
WD_ERASE
1010 1100
1010 1100
0010 H000
0100 H000
0100 1100
1010 0000
1100 0000
1100 0001
1100 0010
Byte 1
WD_EEPROM
value.
MSB
MSB
0101 0011
100x xxxx
000a aaaa
000x xxxx
000a aaaa
000x xxaa
000x xxaa
0000 0000
00xx xxaa
Byte 2
before programming the next byte. See
Instruction Format
xxxx xxxx
xxxx xxxx
bbbb bbbb
xxbb bbbb
bbxx xxxx
bbbb bbbb
bbbb bbbb
0000 00bb
bbbb bb00
Byte 3
xxxx xxxx Enable Serial Programming after RESET
xxxx xxxx Chip Erase EEPROM and Flash.
oooo oooo Read H (high or low) data o from
iiii iiii Write H (high or low) data i to Program
xxxx xxxx Write Program Memory Page at address
oooo oooo Read data o from EEPROM memory at
iiii iiii Write data i to EEPROM memory at
iiii iiii Load data i to EEPROM memory page
xxxx xxxx
Byte4
Operation
goes low.
Program memory at word address a:b.
Memory page at word address b. Data
low byte must be loaded before Data
high byte is applied within the same
address.
a:b.
address a:b.
address a:b.
buffer. After data is loaded, program
EEPROM page.
Write EEPROM page at address a:b.
Minimum Wait Delay
Table 6-127 on page 318
4.5ms
3.6ms
9.0ms
LSB
LSB
9111H–AUTO–01/11
for