PIC18F86J50T-I/PT Microchip Technology, PIC18F86J50T-I/PT Datasheet - Page 37

• Manufacturer Part Number: PIC18F86J50T-I/PT
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,TQFP,64PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F86J50T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 65
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3904 B
• Interface Type: I2C, MSSP, SPI, EUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 65
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183022, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162087 - HEADER MPLAB ICD2 18F87J50 68/84MA180021 - MODULE PLUG-IN 18F87J50 FS USBAC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18F86J50T-I/PTTR

2.2.2
In HS and HSPLL Oscillator modes, a crystal or
ceramic resonator is connected to the OSC1 and
OSC2 pins to establish oscillation. Figure 2-2 shows
the pin connections.
The oscillator design requires the use of a parallel cut
crystal.
FIGURE 2-2:
TABLE 2-2:
© 2009 Microchip Technology Inc.
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following Table 2-3 for additional
information.
Note 1: See Table 2-2 and Table 2-3 for initial values of
Note:
DD
Mode
HS
and temperature range for the application.
C1
C2
2: A series resistor (R
3: R
(1)
(1)
Typical Capacitor Values Used:
C1 and C2.
strip cut crystals.
CRYSTAL OSCILLATOR/CERAMIC
RESONATORS
Use of a series cut crystal may give a fre-
quency out of the crystal manufacturer’s
specifications.
F
16.0 MHz
varies with the oscillator mode chosen.
XTAL
R
8.0 MHz
S
Freq
(2)
Resonators Used:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
OSC2
OSC1
16.0 MHz
CRYSTAL/CERAMIC
RESONATOR OPERATION
(XT, HS OR HSPLL
CONFIGURATION)
4.0 MHz
8.0 MHz
S
) may be required for AT
OSC1
27 pF
22 pF
R
F
(3)
PIC18F87J50
Sleep
OSC2
27 pF
22 pF
To
Internal
Logic
PIC18F87J50 FAMILY
TABLE 2-3:
An internal postscaler allows users to select a clock
frequency other than that of the crystal or resonator.
Frequency division is determined by the CPDIV
Configuration bits. Users may select a clock frequency
of the oscillator frequency, or 1/2, 1/3 or 1/6 of the
frequency.
An external clock may also be used when the micro-
controller is in HS Oscillator mode. In this case, the
OSC2/CLKO pin is left open (Figure 2-3).
Capacitor values are for design guidance only.
These capacitors were tested with the crystals listed
below for basic start-up and operation. These values
are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following this table for additional
information.
Osc Type
DD
Note 1: Higher capacitance increases the stability
HS
and temperature range for the application.
2: When operating below 3V V
3: Since each resonator/crystal has its own
4: Rs may be required to avoid overdriving
5: Always verify oscillator performance over
of oscillator but also increases the
start-up time.
using certain ceramic resonators at any
voltage, it may be necessary to use the
HS mode or switch to a crystal oscillator.
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
components.
crystals with low drive level specification.
the V
expected for the application.
20 MHz
Crystal
4 MHz
8 MHz
Freq
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
DD
Crystals Used:
and temperature range that is
20 MHz
4 MHz
8 MHz
Typical Capacitor Values
values
27 pF
22 pF
15 pF
C1
Tested:
DS39775C-page 37
of
DD
, or when
27 pF
22 pF
15 pF
external
C2