pef2256e Infineon Technologies Corporation, pef2256e Datasheet - Page 241
pef2256e
Manufacturer Part Number
pef2256e
Description
E1/t1/j1 Framer And Line Interface Component For Long- And Short-haul Applications
Manufacturer
Infineon Technologies Corporation
Datasheet
1.PEF2256E.pdf
(518 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
pef2256eV2.1ES
Manufacturer:
HARRIS
Quantity:
101
Company:
Part Number:
pef2256eV2.2
Manufacturer:
INFINEON
Quantity:
513
- Current page: 241 of 518
- Download datasheet (6Mb)
PMOD
XFS
ECM
SSD0
XAIS
User’s Manual
Hardware Description
PCM Mode
For E1 application this bit must be set low. Switching from E1 to T1 or
vice versa the device needs up to 20 µs to settle up to the internal
clocking.
0 =
1 =
Transmit Framing Select
Selection of the transmit framing format can be done independently
of the receive framing format.
0 =
1 =
Error Counter Mode
The function of the error counters is determined by this bit.
0 =
1 =
Select System Data Rate 0
FMR1.SSD0 and SIC1.SSD1 define the data rate on the system
highway. Programming is done with SSD1/SSD0 in the following
table.
00 = 2.048 Mbit/s
01 = 4.096 Mbit/s
10 = 8.192 Mbit/s
11 = 16.384 Mbit/s
Transmit AIS Towards Remote End
Sends AIS on ports XL1, XL2, XOID towards the remote end. The
outgoing data stream which can be looped back through the local loop
to the system interface is not affected.
PCM 30 or E1 mode.
PCM 24 or T1/J1 mode (see RC0.SJR for T1/J1 selection).
Before reading an error counter the corresponding bit in the
Disable Error Counter register (DEC) has to be set. In 8 bit
access the low byte of the error counter should always be read
before the high byte. The error counters are reset with the rising
edge of the corresponding bits in the DEC register.
Every second the error counter is latched and then
automatically reset. The latched error counter state should be
read within the next second. Reading the error counter during
updating should be avoided (do not access an error counter
within 1 µs after the one-second interrupt occurs).
Doubleframe format enabled.
CRC4-multiframe format enabled.
241
DS1.1, 2003-10-23
PEF 2256 H/E
E1 Registers
FALC
®
56
Related parts for pef2256e
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PHASE SHIFTERS
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
PHASE SHIFTERS
Manufacturer:
MERRIMAC [Merrimac Industries, Inc.]
Datasheet:
Part Number:
Description:
Antenna Switch Silicon Pin Diode
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Silicon Switching Diodes
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Single Igbt Driver Ic
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
5 Volt Standard Regulator
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Active Biased Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Small Signal Mosfet 20v?800v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Sipmos Small-signal Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v Small-signal-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
P-channel Mosfets Power-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet: