SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 825

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

38.5.9
38.5.10
38.5.11
6438G–ATARM–19-Apr-11
Speed Identification
USB V2.0 High Speed Global Interrupt
Endpoint Interrupts
The high speed reset is managed by the hardware.
At the connection, the host makes a reset which could be a classic reset (full speed) or a high
speed reset.
At the end of the reset process (full or high), the ENDRESET interrupt is generated.
Then the CPU should read the SPEED bit in UDPHS_INTSTAx to ascertain the speed mode of
the device.
Interrupts are defined in
in
Interrupts are enabled in UDPHS_IEN (see
and individually masked in UDPHS_EPTCTLENBx (see
Control Enable
.
Table 38-4.
SHRT_PCKT
BUSY_BANK
NAK_OUT
NAK_IN/ERR_FLUSH
STALL_SNT/ERR_CRISO/ERR_NB_TRA
RX_SETUP/ERR_FL_ISO
TX_PK_RD /ERR_TRANS
TX_COMPLT
RX_BK_RDY
ERR_OVFLW
MDATA_RX
DATAX_RX
Section 38.6.4 ”UDPHS Interrupt Status Register”
Endpoint Interrupt Source Masks
Register”).
Section 38.6.3 ”UDPHS Interrupt Enable Register”
Section 38.6.3 ”UDPHS Interrupt Enable
Short Packet Interrupt
NAKOUT Interrupt
NAKIN/Error Flush Interrupt
Stall Sent/CRC error/Number of Transaction
Error Interrupt
Received SETUP/Error Flow Interrupt
Transmitted IN Data Complete Interrupt
Received OUT Data Interrupt
Overflow Error Interrupt
MDATA Interrupt
DATAx Interrupt
Busy Bank Interrupt
TX Packet Read/Transaction Error Interrupt
(UDPHS_INTSTA).
Section 38.6.12 ”UDPHS Endpoint
(UDPHS_IEN) and
SAM9G45
Register”)
825