SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 605

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 33-54. Slave Node with PDC
33.7.8.25
33.7.8.26
6438G–ATARM–19-Apr-11
WRITE BUFFER
DATA N
DATA 0
|
|
|
|
Wake-up Request
Bus Idle Time-out
(DMA)
PDC
T h e R E A D b u f f e r c o n t a i n s t h e D A T A i f t h e U S A R T r e c e i v e s t h e r e s p o n s e
(NACT=SUBSCRIBE).
Any node in a sleeping LIN cluster may request a wake-up.
In the LIN 2.0 specification, the wakeup request is issued by forcing the bus to the dominant
state from 250 μs to 5 ms. For this, it is necessary to send the character 0xF0 in order to impose
5 successive dominant bits. Whatever the baud rate is, this character respects the specified
timings.
In the LIN 1.3 specification, the wakeup request should be generated with the character 0x80 in
order to impose 8 successive dominant bits.
The user can choose by the WKUPTYP bit in the LIN Mode register (US_LINMR) either to send
a LIN 2.0 wakeup request (WKUPTYP=0) or to send a LIN 1.3 wakeup request (WKUPTYP=1).
A wake-up request is transmitted by writing the Control Register (US_CR) with the LINWKUP bit
at 1. Once the transfer is completed, the LINTC flag is asserted in the Status Register (US_SR).
It is cleared by writing the Control Register (US_CR) with the RSTSTA bit at 1.
If the LIN bus is inactive for a certain duration, the slave nodes shall automatically enter in sleep
mode. In the LIN 2.0 specification, this time-out is fixed at 4 seconds. In the LIN 1.3 specifica-
tion, it is fixed at 25000 Tbits.
In Slave Node configuration, the Receiver Time-out detects an idle condition on the RXD line.
When a time-out is detected, the bit TIMEOUT in the Channel Status Register (US_CSR) rises
and can generate an interrupt, thus indicating to the driver to go into sleep mode.
The time-out delay period (during which the receiver waits for a new character) is programmed
in the TO field of the Receiver Time-out Register (US_RTOR). If the TO field is programmed at
0, the Receiver Time-out is disabled and no time-out is detected. The TIMEOUT bit in US_CSR
remains at 0. Otherwise, the receiver loads a 17-bit counter with the value programmed in TO.
This counter is decremented at each bit period and reloaded each time a new character is
received. If the counter reaches 0, the TIMEOUT bit in the Status Register rises.
If STTTO is performed, the counter clock is stopped until a first character is received.
If RETTO is performed, the counter starts counting down immediately from the value TO.
• Baud rate min = 1 kbit/s -> Tbit = 1ms -> 5 Tbits = 5 ms
• Baud rate max = 20 kbit/s -> Tbi t= 50 μs -> 5 Tbits = 250 μs
APB bus
TXRDY
LIN CONTROLLER
USART3
READ BUFFER
DATA N
DATA 0
|
|
|
|
(DMA)
PDC
APB bus
RXRDY
SAM9G45
NACT = SUBSCRIBE
LIN CONTROLLER
USART3
605