SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 623

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

• FRAME: Framing Error
0: No stop bit has been detected low since the last RSTSTA.
1: At least one stop bit has been detected low since the last RSTSTA.
• PARE: Parity Error
0: No parity error has been detected since the last RSTSTA.
1: At least one parity error has been detected since the last RSTSTA.
• TIMEOUT: Receiver Time-out
0: There has not been a time-out since the last Start Time-out command (STTTO in US_CR) or the Time-out Register is 0.
1: There has been a time-out since the last Start Time-out command (STTTO in US_CR).
• TXEMPTY: Transmitter Empty
0: There are characters in either US_THR or the Transmit Shift Register, or the transmitter is disabled.
1: There are no characters in US_THR, nor in the Transmit Shift Register.
• ITER/UNRE: Max number of Repetitions Reached or SPI Underrun Error
ITER = 0: Maximum number of repetitions has not been reached since the last RSTSTA.
ITER = 1: Maximum number of repetitions has been reached since the last RSTSTA.
UNRE = 0: No SPI underrun error has occurred since the last RSTSTA.
UNRE = 1: At least one SPI underrun error has occurred since the last RSTSTA.
• TXBUFE: Transmission Buffer Empty
0: The signal Buffer Empty from the Transmit PDC channel is inactive.
1: The signal Buffer Empty from the Transmit PDC channel is active.
• RXBUFF: Reception Buffer Full
0: The signal Buffer Full from the Receive PDC channel is inactive.
1: The signal Buffer Full from the Receive PDC channel is active.
• NACK/LINBK Non Acknowledge or LIN Break Sent or LIN Break Received
0: No Non Acknowledge has not been detected since the last RSTNACK.
0: No LIN Break has been sent since the last RSTSTA.
0: No LIN Break has received sent since the last RSTSTA.
6438G–ATARM–19-Apr-11
– If USART does not operate in SPI Slave Mode (USART_MODE
– If USART operates in SPI Slave Mode (USART_MODE = 0xF):
– If USART does not operate in LIN Mode (USART_MODE
– 1: At least one Non Acknowledge has been detected since the last RSTNACK.If USART operates in LIN Master
– 1:At least one LIN Break has been sent since the last RSTSTAIf USART operates in LIN Slave Mode
– 1:At least one LIN Break has been received since the last RSTSTA.LINID: LIN Identifier Sent or LIN
Mode (USART_MODE = 0xA):
(USART_MODE = 0xB):
Identifier ReceivedIf USART operates in LIN Master Mode (USART_MODE = 0xA):
0xA AND
0xF):
0xB):
SAM9G45
623