DF2148RTE20IV Renesas Electronics America, DF2148RTE20IV Datasheet - Page 729
DF2148RTE20IV
Manufacturer Part Number
DF2148RTE20IV
Description
MCU 5V 128K I-TEMP,PB-FREE, 100-
Manufacturer
Renesas Electronics America
Series
H8® H8S/2100r
Specifications of DF2148RTE20IV
Core Processor
H8S/2000
Core Size
16-Bit
Speed
20MHz
Connectivity
Host Interface, I²C, IrDA, SCI
Peripherals
POR, PWM, WDT
Number Of I /o
74
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 8x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 729 of 1179
- Download datasheet (7Mb)
22.10.10 Notes on Memory Programming
Notes: 1. The flash memory is initially in the erased state when the device is shipped by Renesas.
22.11
Precautions concerning the use of on-board programming mode and programmer mode are
summarized below.
Use the specified voltages and timing for programming and erasing.
Applied voltages in excess of the rating can permanently damage the device. For a PROM
programmer, use Renesas Technology microcomputer device types with 128-kbyte or 64-kbyte
on-chip flash memory that support a 5.0-V programming voltage.
Do not select the HN28F101 or use a programming voltage of 3.3 V for the PROM programmer,
and only use the specified socket adapter. Incorrect use will result in damaging the device.
Powering on and off
When applying or disconnecting V
hardware protection state.
The power-on and power-off timing requirements should also be satisfied in the event of a power
failure and subsequent recovery.
Use the recommended algorithm when programming and erasing flash memory.
The recommended algorithm enables programming and erasing to be carried out without
subjecting the device to voltage stress or sacrificing program data reliability. When setting the P or
E bit in FLMCR1, the watchdog timer should be set beforehand as a precaution against program
runaway, etc.
Do not set or clear the SWE bit during program execution in flash memory.
Clear the SWE bit before executing a program or reading data in flash memory. When the SWE
bit is set, data in flash memory can be rewritten, but flash memory should only be accessed for
verify operations (verification during programming/erasing).
When programming addresses which have previously been programmed, carry out auto-
erasing before auto-programming.
When performing programming using programmer mode on a chip that has been
programmed/erased in an on-board programming mode, auto-erasing is recommended before
carrying out auto-programming.
2. Auto-programming should be performed once only on the same address block.
Flash Memory Programming and Erasing Precautions
Section 22 ROM
For other chips for which the erasure history is unknown, it is recommended that auto-
erasing be executed to check and supplement the initialization (erase) level.
(Mask ROM Version, H8S/2148 F-ZTAT, H8S/2147N F-ZTAT, H8S/2144 F-ZTAT, and H8S/2142 F-ZTAT)
CC
, fix the RES pin low and place the flash memory in the
Rev. 4.00 Sep 27, 2006 page 683 of 1130
REJ09B0327-0400
Related parts for DF2148RTE20IV
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: