DF2148RTE20IV Renesas Electronics America, DF2148RTE20IV Datasheet - Page 179
DF2148RTE20IV
Manufacturer Part Number
DF2148RTE20IV
Description
MCU 5V 128K I-TEMP,PB-FREE, 100-
Manufacturer
Renesas Electronics America
Series
H8® H8S/2100r
Specifications of DF2148RTE20IV
Core Processor
H8S/2000
Core Size
16-Bit
Speed
20MHz
Connectivity
Host Interface, I²C, IrDA, SCI
Peripherals
POR, PWM, WDT
Number Of I /o
74
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 8x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 179 of 1179
- Download datasheet (7Mb)
5.4.3
ABRKCR and BAR settings can be made so that an address break interrupt is generated when the
CPU prefetches the address set in BAR. This address break function issues an interrupt request to
the interrupt controller when the address is prefetched, and the interrupt controller determines the
interrupt priority. When the interrupt is accepted, interrupt exception handling is started on
completion of the currently executing instruction. With an address break interrupt, interrupt mask
control by the I and UI bits in the CPU’s CCR is ineffective.
The register settings when the address break function is used are as follows.
1. Set the break address in bits A23 to A1 in BAR.
2. Set the BIE bit in ABRKCR to 1 to enable address breaks. An address break will not be
When the setting condition occurs, the CMF flag in ABRKCR is set to 1 and an interrupt is
requested. If necessary, the source should be identified in the interrupt handling routine.
5.4.4
requested if the BIE bit is cleared to 0.
With the address break function, the address at which the first instruction byte is located
should be specified as the break address. Occurrence of the address break condition may not be
recognized for other addresses.
In normal mode, no comparison is made with address lines A23 to A16.
If a branch instruction (Bcc, BSR), jump instruction (JMP, JSR), RTS instruction, or RTE
instruction is located immediately before the address set in BAR, execution of this instruction
will output a prefetch signal for that address, and an address break may be requested. This can
be prevented by not making a break address setting for an address immediately following one
of these instructions, or by determining within the interrupt handling routine whether interrupt
handling was initiated by a genuine condition occurrence.
As an address break interrupt is generated by a combination of the internal prefetch signal and
address, the timing of the start of interrupt exception handling depends on the content and
execution cycle of the instruction at the set address and the preceding instruction. Figure 5.6
shows some address timing examples.
Operation
Usage Notes
Rev. 4.00 Sep 27, 2006 page 133 of 1130
Section 5 Interrupt Controller
REJ09B0327-0400
Related parts for DF2148RTE20IV
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: