MC9S12DT256MPVE Freescale Semiconductor, MC9S12DT256MPVE Datasheet - Page 413

• Manufacturer Part Number: MC9S12DT256MPVE
• Description: IC MCU 256K FLASH 25MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12DT256MPVE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SCI, SPI
• Peripherals: PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.25 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 112-LQFP
• Processor Series: S12D
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 1
• Operating Supply Voltage: 5 V to 2.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68KIT912DP256
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (8-ch x 10-bit)
• No. Of I/o's: 91
• Eeprom Memory Size: 4KB
• Ram Memory Size: 12KB
• Cpu Speed: 25MHz
• No. Of Timers: 1
• No. Of Pwm Channels: 8
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.5
The reset state of each individual bit is listed in
details the registers and their bit-fields.
9.6
IICV2 uses only one interrupt vector.
Internally there are three types of interrupts in IIC. The interrupt service routine can determine the interrupt
type by reading the status register.
IIC Interrupt can be generated on
The IIC interrupt is enabled by the IBIE bit in the IIC control register. It must be cleared by writing 0 to
the IBF bit in the interrupt service routine.
9.7
9.7.1
9.7.1.1
Reset will put the IIC bus control register to its default status. Before the interface can be used to transfer
serial data, an initialization procedure must be carried out, as follows:
Freescale Semiconductor
1. Arbitration lost condition (IBAL bit set)
2. Byte transfer condition (TCF bit set)
3. Address detect condition (IAAS bit set)
1. Update the frequency divider register (IBFD) and select the required division ratio to obtain SCL
2. Update the IIC bus address register (IBAD) to define its slave address.
3. Set the IBEN bit of the IIC bus control register (IBCR) to enable the IIC interface system.
4. Modify the bits of the IIC bus control register (IBCR) to select master/slave mode, transmit/receive
frequency from system clock.
mode and interrupt enable or not.
Interrupt
Interrupt
Resets
Interrupts
Initialization/Application Information
IIC
IIC Programming Examples
Initialization Sequence
Offset
—
Vector
—
MC9S12XDP512 Data Sheet, Rev. 2.21
Priority
Table 9-8. Interrupt Summary
—
IBAL, TCF, IAAS
Section 9.3, “Memory Map and Register
bits in IBSR
Source
register
Chapter 9 Inter-Integrated Circuit (IICV2) Block Description
When either of IBAL, TCF or IAAS bits is set
may cause an interrupt based on arbitration
lost, transfer complete or address detect
conditions
Description
Definition,” which
413