MCHC912B32CFUE8 Freescale Semiconductor, MCHC912B32CFUE8 Datasheet - Page 215

• Manufacturer Part Number: MCHC912B32CFUE8
• Description: IC MCU 32K FLASH 8MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC12r

Specifications of MCHC912B32CFUE8

• Core Processor: CPU12
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 63
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 768 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Cpu Family: HC12
• Device Core Size: 16b
• Frequency (max): 8MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 1KB
• # I/os (max): 63
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 80
• Package Type: PQFP
• Package: 80PQFP
• Family Name: HC12
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 63
• Processor Series: HC912B
• Core: HC12
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 8 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912B32E
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.4.1 Power Off Mode
For guaranteed BDLC operation, this mode is entered from reset mode when the BDLC supply voltage,
V
(LVR) before being powered down. In power off mode, the pin input and output specifications are not
guaranteed.
15.4.2 Reset Mode
This mode is entered from power off mode when the BDLC supply voltage, V
specified value (V
asserted while powering up the BDLC or an unknown state is entered and correct operation cannot be
guaranteed. Reset mode is also entered from any other mode when any reset source is asserted.
In reset mode, the internal BDLC voltage references are operative, V
which are held in their reset state, and the internal BDLC system clock is running. Registers assume their
reset condition. Because outputs are held in their programmed reset state, inputs and network activity are
ignored.
15.4.3 Run Mode
This mode is entered from reset mode after all MCU reset sources are no longer asserted. Run mode is
entered from the BDLC wait mode when activity is sensed on the J1850 bus.
Run mode is entered from the BDLC stop mode when network activity is sensed, although messages are
not received properly until the clocks have stabilized and the CPU is also in run mode.
In this mode, normal network operation takes place. Ensure that all BDLC transmissions have ceased
before exiting this mode.
15.5 Power-Conserving Modes
The BDLC has three power-conserving modes:
Depending upon the logic level of the WCM bit in BDLC control register 1 (BCR1), the BDLC enters a
power-conserving mode when the CPU executes the STOP or WAIT instruction.
When a power-conserving mode is entered, any activity on the J1850 network causes the BDLC to exit
low-power mode. When exiting from BDLC stop mode, the BDLC generates an unmaskable interrupt of
the CPU. This wakeup interrupt state is reflected in the BDLC state vector register (BSVR) and encoded
as the highest priority interrupt.
Wait mode or stop mode does not reset the BDLC registers upon BDLC wakeup.
Freescale Semiconductor
DD
1. BDLC wait and CPU wait mode
2. BDLC stop and CPU wait mode
3. BDLC stop and CPU stop mode
, drops below its minimum specified value. The BDLC is placed in reset mode by low-voltage reset
DD
–10%) and an MCU reset source is asserted. The internal MCU reset must be
M68HC12B Family Data Sheet, Rev. 9.1
DD
is supplied to the internal circuits
DD
, rises above its minimum
Power-Conserving Modes
215