SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 737

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

37.6.2
37.6.2.1
37.6.2.2
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
PWM Channel
Block Diagram
Waveform Properties
Each linear divider can independently divide one of the clocks of the modulo n counter. The
selection of the clock to be divided is made according to the PREA (PREB) field of the PWM
Mode register (PWM_MR). The resulting clock clkA (clkB) is the clock selected divided by DIVA
(DIVB) field value in the PWM Mode register (PWM_MR).
After a reset of the PWM controller, DIVA (DIVB) and PREA (PREB) in the PWM Mode register
are set to 0. This implies that after reset clkA (clkB) are turned off.
At reset, all clocks provided by the modulo n counter are turned off except clock “clk”. This situa-
tion is also true when the PWM master clock is turned off through the Power Management
Controller.
Figure 37-3. Functional View of the Channel Block Diagram
Each of the 4 channels is composed of three blocks:
The different properties of output waveforms are:
• A clock selector which selects one of the clocks provided by the clock generator described in
• An internal counter clocked by the output of the clock selector. This internal counter is
• A comparator used to generate events according to the internal counter value. It also
• the internal clock selection. The internal channel counter is clocked by one of the clocks
• the waveform period. This channel parameter is defined in the CPRD field of the
inputs from
from clock
generator
APB bus
Section 37.6.1 “PWM Clock Generator” on page
incremented or decremented according to the channel configuration and comparators events.
The size of the internal counter is 16 bits.
computes the PWMx output waveform according to the configuration.
provided by the clock generator described in the previous section. This channel parameter is
defined in the CPRE field of the PWM_CMRx register. This field is reset at 0.
PWM_CPRDx register.
- If the waveform is left aligned, then the output waveform period depends on the counter
inputs
– a modulo n counter which provides 11 clocks: F
– two linear dividers (1, 1/2, 1/3, ... 1/255) that provide two separate clocks: clkA and
F
clkB
MCK
/16, F
Channel
Selector
Clock
MCK
/32, F
MCK
/64, F
MCK
Counter
Internal
/128, F
MCK
/256, F
736.
MCK
MCK
Comparator
, F
MCK
/512, F
/2, F
MCK
MCK
/1024
/4, F
SAM9G35
SAM9G35
MCK
/8,
PWMx
output waveform
737
737