SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 594

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

33.7.17
Name:
Address:
Access:
• FRCESTALL: Stall Handshake Request
0 = no effect.
1= If set a STALL answer will be done to the host for the next handshake.
This bit is reset by hardware upon received SETUP.
• TOGGLESQ_STA: Toggle Sequencing
Toggle Sequencing:
Notes:
594
594
SHRT_PCKT
NAK_OUT
These bits are set by hardware to indicate the PID data of the current bank:
Value
– IN endpoint: it indicates the PID Data Toggle that will be used for the next packet sent. This is not relative to
– CONTROL and OUT endpoint:
31
23
15
0
1
2
3
7
TOGGLESQ_STA
the current bank.
1. In OUT transfer, the Toggle information is meaningful only when the current bank is busy (Received OUT Data = 1).
2. These bits are updated for OUT transfer:
3. For High Bandwidth Isochronous Out endpoint, it is recommended to check the UDPHS_EPTSTAx/ERR_TRANS bit to know
4. This field is reset to DATA1 by the UDPHS_EPTCLRSTAx register TOGGLESQ bit, and by UDPHS_EPTCTLDISx (disable
SAM9G35
SAM9G35
UDPHS Endpoint Status Register
-
-
if the toggle sequencing is correct or not.
endpoint).
a new data has been written into the current bank.
the user has just cleared the Received OUT Data bit to switch to the next bank.
UDPHS_EPTSTAx [x=0..6]
0xF803C11C [0], 0xF803C13C [1], 0xF803C15C [2], 0xF803C17C [3], 0xF803C19C [4], 0xF803C1BC [5],
0xF803C1DC [6]
Read-only
Name
DATA0
DATA1
DATA2
MDATA
ERR_FLUSH
NAK_IN/
30
22
14
6
BYTE_COUNT
Description
DATA0
DATA1
Data2 (only for High Bandwidth Isochronous Endpoint)
MData (only for High Bandwidth Isochronous Endpoint)
ERR_CRISO/
ERR_NBTRA
STALL_SNT/
FRCESTALL
29
21
13
5
ERR_FL_ISO
RX_SETUP/
28
20
12
4
–
BYTE_COUNT
TX_PK_RDY/
ERR_TRANS
27
19
11
BUSY_BANK_STA
3
–
TX_COMPLT
26
18
10
2
–
RX_BK_RDY/
KILL_BANK
25
17
CURRENT_BANK/
9
1
–
CONTROL_DIR
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
ERR_OVFLW
24
16
8
0
–