ATTINY20-XU Atmel, ATTINY20-XU Datasheet - Page 79

• Manufacturer Part Number: ATTINY20-XU
• Description: MCU AVR 2KB FLASH 12MHZ 14TSSOP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY20-XU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Processor Series: ATtiny
• Core: AVR
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, TWI
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

12.2.1
12.2.2
8235B–AVR–04/11
Registers
Definitions
Most register and bit references in this section are written in general form. A lower case “n”
replaces the Timer/Counter number, and a lower case “x” replaces the Output Compare unit
channel. However, when using the register or bit defines in a program, the precise form must be
used, i.e., TCNT1 for accessing Timer/Counter1 counter value and so on.
The Timer/Counter (TCNT1), Output Compare Registers (OCR1A/B), and Input Capture Regis-
ter (ICR1) are all 16-bit registers. Special procedures must be followed when accessing the 16-
bit registers. These procedures are described in section
95. The Timer/Counter Control Registers (TCCR1A/B) are 8-bit registers and have no CPU
access restrictions. Interrupt requests (abbreviated to Int.Req. in the figure) signals are all visible
in the Timer Interrupt Flag Register (TIFR). All interrupts are individually masked with the Timer
Interrupt Mask Register (TIMSK). TIFR and TIMSK are not shown in the figure.
The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on
the T1 pin. The Clock Select logic block controls which clock source and edge the Timer/Counter
uses to increment (or decrement) its value. The Timer/Counter is inactive when no clock source
is selected. The output from the Clock Select logic is referred to as the timer clock (clk
The double buffered Output Compare Registers (OCR1A/B) are compared with the Timer/Coun-
ter value at all time. The result of the compare can be used by the Waveform Generator to
generate a PWM or variable frequency output on the Output Compare pin (OC1A/B). See
put Compare Units” on page
Flag (OCF1A/B) which can be used to generate an Output Compare interrupt request.
The Input Capture Register can capture the Timer/Counter value at a given external (edge trig-
gered) event on either the Input Capture pin (ICP1) or on the Analog Comparator pins (See
“Analog Comparator” on page
Canceler) for reducing the chance of capturing noise spikes.
The TOP value, or maximum Timer/Counter value, can in some modes of operation be defined
by either the OCR1A Register, the ICR1 Register, or by a set of fixed values. When using
OCR1A as TOP value in a PWM mode, the OCR1A Register can not be used for generating a
PWM output. However, the TOP value will in this case be double buffered allowing the TOP
value to be changed in run time. If a fixed TOP value is required, the ICR1 Register can be used
as an alternative, freeing the OCR1A to be used as PWM output.
The following definitions are used extensively throughout the section:
Table 12-1.
Constant
BOTTOM
MAX
TOP
Definitions
Description
The counter reaches BOTTOM when it becomes 0x00
The counter reaches TOP when it becomes equal to the highest value in the count
sequence. The TOP value can be assigned to be the fixed value 0xFF (MAX), the value
stored in the OCR
depends on the mode of operation
The counter reaches its MAXimum when it becomes 0xFF (decimal 255)
83. The compare match event will also set the Compare Match
108). The Input Capture unit includes a digital filtering unit (Noise
1
A register, or the value stored in the ICR1 register. The assignment
“Accessing 16-bit Registers” on page
ATtiny20
T1
).
“Out-
79