ATTINY20-XU Atmel, ATTINY20-XU Datasheet - Page 29

• Manufacturer Part Number: ATTINY20-XU
• Description: MCU AVR 2KB FLASH 12MHZ 14TSSOP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY20-XU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Processor Series: ATtiny
• Core: AVR
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, TWI
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

7.5.2
8235B–AVR–04/11
PRR – Power Reduction Register
Table 7-2.
• Bit 0 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
• Bits 7:5 – Res: Reserved Bits
These bits are reserved and will always read as zero.
• Bit 4 – PRTWI: Power Reduction Two-Wire Interface
Writing a logic one to this bit shuts down the Two-Wire Interface module.
• Bit 3 – PRSPI: Power Reduction Serial Peripheral Interface
Writing a logic one to this bit shuts down the Serial Peripheral Interface module.
• Bit 2 – PRTIM1: Power Reduction Timer/Counter1
Writing a logic one to this bit shuts down the Timer/Counter1 module. When the Timer/Counter1
is enabled, operation will continue like before the shutdown.
• Bit 1 – PRTIM0: Power Reduction Timer/Counter0
Writing a logic one to this bit shuts down the Timer/Counter0 module. When the Timer/Counter0
is enabled, operation will continue like before the shutdown.
• Bit 0 – PRADC: Power Reduction ADC
Writing a logic one to this bit shuts down the ADC. The ADC must be disabled before shut down.
The analog comparator cannot use the ADC input MUX when the ADC is shut down.
Bit
0x35
Read/Write
Initial Value
SM2
0
1
1
1
1
Sleep Mode Select (Continued)
R
7
–
0
SM1
1
0
0
1
1
R
6
–
0
R
5
–
0
SM0
1
0
1
0
1
PRTWI
R/W
4
0
PRSPI
Sleep Mode
Reserved
Standby
Reserved
Reserved
Reserved
R/W
3
0
PRTIM1
R/W
2
0
PRTIM0
R/W
1
0
PRADC
R/W
0
0
ATtiny20
PRR
29