MPC564MZP56 Freescale Semiconductor, MPC564MZP56 Datasheet - Page 791

• Manufacturer Part Number: MPC564MZP56
• Description: IC MCU 512K FLASH 56MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Core: PowerPC
• Processor Series: MPC5xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 56 MHz
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 56
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 32
• Height: 1.95 mm
• Interface Type: CAN, JTAG, QSPI, SCI, SPI, UART
• Length: 27 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 2.7 V, 5.25 V
• Supply Voltage (min): 2.5 V, 4.75 V
• Width: 27 mm
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

Freescale Semiconductor
.
Bits
8:15
POL
6:7
0
1
2
3
4
5
0
0
0
1
Control Bits
Name
FREN
TRSP
DDR
POL
EN
PIN
EN
CP
—
0
0
1
0
Pin input status bit — The PIN bit reflects the state present on the MPWMSM signal. The
software can thus monitor the pin state.
The PIN bit is a read-only bit. Writing to the PIN bit has no effect.
Data direction register — The DDR bit indicates the direction for the signal when the PWM
function is not used (disable mode).
0 signal is in input.
1 signal is in output.
The DDR bit is cleared by reset.
Table 17-30
direction register (DDR) bit.
Freeze enable bit — This active high read/write control bit enables the MPWMSM to recognize
the freeze signal on the MIOB.
0 MPWMSM not frozen even if the MIOB freeze line is active.
1 MPWMSM frozen if the MIOB freeze line is active.
The FREN is cleared by reset.
Transparent mode — The TRSP bit indicates that the MPWMSM is in transparent mode. In
transparent mode, when the software writes to either the MPWMPERR or MPWMPULR1 register
the value written is immediately transferred to the counter or register MPWMPULR2 respectively.
0 Double-buffered mode.
1 Transparent mode.
The TRSP bit is cleared by reset.
Output polarity control bit — The POL bit works in conjunction with the EN bit and controls
whether the MPWMSM drives the signal with the direct or the inverted value of the output flip-flop.
Table 17-30
direction register (DDR) bit.
Enable PWM signal generation — The EN bit defines whether the MPWMSM generates a PWM
signal or is used as an I/O channel:
0 PWM generation disabled (signal can be used as I/O).
1 PWM generation enabled (the signal is in output mode).
Each time the submodule is enabled, the value of CP is loaded into the prescaler.
The EN bit is cleared by reset.
Reserved
Clock prescaler — This 8-bit read/write data register stores the modulus value for loading into
the built-in 8-bit clock prescaler. The value loaded defines the divide ratio for the signal that clocks
the MPWMSM. The new value is loaded into the prescaler counter on the prescaler counter
overflow, or upon the EN bit of the MPWMSCR being set.
Table 17-31
DDR
X
0
1
0
Table 17-30. PWMSM Output Signal Polarity Selection
Direction
lists the different uses for the polarity (POL) bit, the enable (EN) bit and the data
lists the different uses for the polarity (POL) bit, the enable (EN) bit and the data
gives the clock divide ratio according to the value of CP.
Table 17-29. MPWMSCR Bit Descriptions
Signal
Output
Output
MPC561/MPC563 Reference Manual, Rev. 1.2
Input
Input
Signal State
Always Low
High Pulse
INPUT
INPUT
Description
Periodic Edge
Falling Edge
—
—
—
Modular Input/Output Subsystem (MIOS14)
Variable Edge
Rising Edge
—
—
—
InterruptIon
Falling Edge
Optional
—
—
—
17-59