MPC564MZP56 Freescale Semiconductor, MPC564MZP56 Datasheet - Page 608

• Manufacturer Part Number: MPC564MZP56
• Description: IC MCU 512K FLASH 56MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Core: PowerPC
• Processor Series: MPC5xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 56 MHz
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 56
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 32
• Height: 1.95 mm
• Interface Type: CAN, JTAG, QSPI, SCI, SPI, UART
• Length: 27 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 2.7 V, 5.25 V
• Supply Voltage (min): 2.5 V, 4.75 V
• Width: 27 mm
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

QADC64E Enhanced Mode Operation
Each port A or B signal is configured as an input or output by programming the port data direction register
(DDRQA or DDRQB). The digital input signal states are read by the software in the upper half of the port
data register when the port data direction register specifies that the signals are inputs. The digital data in
the port data register is driven onto the port A or B signals when the corresponding bit in the port data
direction register specifies output. Refer to
Since the outputs are configured as push-pull drivers, external pull-up provisions are not necessary when
the output is used to drive another integrated circuit.
14.6.2
The QADC64E uses two external trigger signals (ETRIG[2:1]). Each of the two input external trigger
signals is associated with one of the scan queues, queue 1 or queue 2 The assignment of ETRIG[2:1] to a
queue is made in the QACR0 register by the TRG bit. When TRG=0, ETRIG1 triggers queue 1 and
ETRIG2 triggers queue 2. When TRG=1, ETRIG1 triggers queue 2 and ETRIG2 triggers queue 1.
14.6.3
V
power is required to isolate the sensitive analog circuitry from the normal levels of noise present on the
digital power supply. Refer to
The analog supply signals (V
V
14-66
DDA
RL
) and of the analog multiplexer inputs.
16 CHANNELS
and V
External Trigger Input Signals
Analog Power Signals
SSA
signals supply power to the analog subsystems of the QADC64E module. Dedicated
DDA
Figure 14-47. Equivalent Analog Input Circuitry
Appendix F, “Electrical
MPC561/MPC563 Reference Manual, Rev. 1.2
and V
SSA
) define the limits of the analog reference voltages (V
Figure 14-47
C
Appendix B, “Internal Memory
SAMPLE
P
AMP
V
V
DDA
SSA
Characteristics,” for more information.
is a diagram of the analog input circuitry.
S/H
RC DAC
Comparator
V
RH
V
RL
QADC64E 16CH SAMPLE AMP
Map” for more information.
Freescale Semiconductor
RH
and