AC162078 Microchip Technology, AC162078 Datasheet - Page 19

• Manufacturer Part Number: AC162078
• Description: HEADER INTRFC MPLAB ICD2 18F1330
• Manufacturer: Microchip Technology

Specifications of AC162078

• Accessory Type: Transition Header
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: ICD2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Not applicable / Not applicable

2.3
The
functions: Device Reset, and Device Programming
and Debugging. If programming and debugging are
not required in the end application, a direct
connection to V
addition of other components, to help increase the
application’s resistance to spurious Resets from
voltage
configuration is shown in Figure 2-1. Other circuit
designs may be implemented, depending on the
application’s requirements.
During programming and debugging, the resistance
and capacitance that can be added to the pin must be
considered. Device programmers and debuggers drive
the MCLR pin. Consequently, specific voltage levels
(V
adversely affected. Therefore, specific values of R1
and C1 will need to be adjusted based on the
application and PCB requirements. For example, it is
recommended that the capacitor, C1, be isolated from
the MCLR pin during programming and debugging
operations by using a jumper (Figure 2-2). The jumper
is replaced for normal run-time operations.
Any components associated with the MCLR pin
should be placed within 0.25 inch (6 mm) of the pin.
FIGURE 2-2:
 2009 Microchip Technology Inc.
IH
Note 1: R1  10 k is recommended. A suggested
and V
MCLR
2: R2  470 will limit any current flowing into
Master Clear (MCLR) Pin
sags,
IL
starting value is 10 k. Ensure that the
MCLR pin V
MCLR from the external capacitor, C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
V
V
) and fast signal transitions must not be
DD
IH
pin
R1
JP
C1
and V
DD
may
may be all that is required. The
provides
IL
EXAMPLE OF MCLR PIN
CONNECTIONS
specifications are met.
IH
R2
and V
be
MCLR
IL
beneficial.
PIC18FXXXX
two
specifications are met.
specific
A
device
typical
2.4
The PGC and PGD pins are used for In-Circuit Serial
Programming™ (ICSP™) and debugging purposes. It
is recommended to keep the trace length between the
ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recom-
mended, with the value in the range of a few tens of
ohms, not to exceed 100Ω.
Pull-up resistors, series diodes, and capacitors on the
PGC and PGD pins are not recommended as they will
interfere with the programmer/debugger communica-
tions to the device. If such discrete components are an
application requirement, they should be removed from
the circuit during programming and debugging. Alter-
natively, refer to the AC/DC characteristics and timing
requirements information in the respective device
Flash programming specification for information on
capacitive loading limits and pin input voltage high (V
and input low (V
For device emulation, ensure that the “Communication
Channel Select” (i.e., PGCx/PGDx pins) programmed
into the device matches the physical connections for
the ICSP to the Microchip debugger/emulator tool.
For
development tools connection requirements, refer to
Section 21.0 “Development Support”.
more
ICSP Pins
PIC18F1230/1330
information
IL
) requirements.
on
available
DS39758D-page 19
Microchip
IH
)