Z8F041APH020SG2156 ZiLOG, Z8F041APH020SG2156 Datasheet - Page 212
Z8F041APH020SG2156
Manufacturer Part Number
Z8F041APH020SG2156
Description
8-bit Microcontrollers - MCU 4K FLASH 1K RAM 128B NVDS
Manufacturer
ZiLOG
Datasheet
1.Z8F082ASJ020EG2156.pdf
(282 pages)
Specifications of Z8F041APH020SG2156
Rohs
yes
Core
eZ8
Processor Series
Z8F041xx
Data Bus Width
8 bit
Maximum Clock Frequency
20 MHz
Program Memory Size
4 KB
Data Ram Size
1 KB
On-chip Adc
Yes
Operating Supply Voltage
2.7 V to 3.6 V
Operating Temperature Range
- 40 C to + 105 C
Package / Case
PDIP-20
Mounting Style
Through Hole
A/d Bit Size
10 bit
A/d Channels Available
8
Interface Type
UART
Maximum Operating Temperature
+ 105 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
17
Number Of Timers
2
Program Memory Type
Flash
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.7 V
- Current page: 212 of 282
- Download datasheet (2Mb)
®
Z8 Encore! XP
F082A Series
Product Specification
195
When selecting a new clock source, the system clock oscillator failure detection circuitry
and the Watchdog Timer oscillator failure circuitry must be disabled. If SOFEN and
WOFEN are not disabled prior to a clock switch-over, it is possible to generate an inter-
rupt for a failure of either oscillator. The Failure detection circuitry can be enabled any-
time after a successful write of OSCSEL in the OSCCTL Register.
The internal precision oscillator is enabled by default. If the user code changes to a differ-
ent oscillator, it may be appropriate to disable the IPO for power savings. Disabling the
IPO does not occur automatically.
Clock Failure Detection and Recovery
Should an oscillator or timer fail, there are methods of recovery, as this section describes.
System Clock Oscillator Failure
The Z8F04xA family devices can generate nonmaskable interrupt-like events when the
primary oscillator fails. To maintain system function in this situation, the clock failure
recovery circuitry automatically forces the Watchdog Timer oscillator to drive the system
clock. The Watchdog Timer oscillator must be enabled to allow the recovery. Although
this oscillator runs at a much slower speed than the original system clock, the CPU contin-
ues to operate, allowing execution of a clock failure vector and software routines that
either remedy the oscillator failure or issue a failure alert. This automatic switch-over is
not available if the Watchdog Timer is selected as the system clock oscillator. It is also
unavailable if the Watchdog Timer oscillator is disabled, though it is not necessary to
enable the Watchdog Timer reset function (see the
Watchdog Timer
chapter on page 93).
The primary oscillator failure detection circuitry asserts if the system clock frequency
drops below 1 kHz ±50%. If an external signal is selected as the system oscillator, it is pos-
sible that a very slow but nonfailing clock can generate a failure condition. Under these
conditions, do not enable the clock failure circuitry (SOFEN must be deasserted in the
OSCCTL Register).
Watchdog Timer Failure
In the event of a Watchdog Timer oscillator failure, a similar nonmaskable interrupt-like
event is issued. This event does not trigger an attendant clock switch-over, but alerts the
CPU of the failure. After a Watchdog Timer failure, it is no longer possible to detect a pri-
mary oscillator failure. The failure detection circuitry does not function if the Watchdog
Timer is used as the system clock oscillator or if the Watchdog Timer oscillator has been
disabled. For either of these cases, it is necessary to disable the detection circuitry by deas-
serting the WDFEN bit of the OSCCTL Register.
The Watchdog Timer oscillator failure detection circuit counts system clocks while look-
ing for a Watchdog Timer clock. The logic counts 8004 system clock cycles before deter-
mining that a failure has occurred. The system clock rate determines the speed at which
PS022827-1212
P R E L I M I N A R Y
Operation
Related parts for Z8F041APH020SG2156
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: