Z8F041APH020SG2156 ZiLOG, Z8F041APH020SG2156 Datasheet - Page 140
Z8F041APH020SG2156
Manufacturer Part Number
Z8F041APH020SG2156
Description
8-bit Microcontrollers - MCU 4K FLASH 1K RAM 128B NVDS
Manufacturer
ZiLOG
Datasheet
1.Z8F082ASJ020EG2156.pdf
(282 pages)
Specifications of Z8F041APH020SG2156
Rohs
yes
Core
eZ8
Processor Series
Z8F041xx
Data Bus Width
8 bit
Maximum Clock Frequency
20 MHz
Program Memory Size
4 KB
Data Ram Size
1 KB
On-chip Adc
Yes
Operating Supply Voltage
2.7 V to 3.6 V
Operating Temperature Range
- 40 C to + 105 C
Package / Case
PDIP-20
Mounting Style
Through Hole
A/d Bit Size
10 bit
A/d Channels Available
8
Interface Type
UART
Maximum Operating Temperature
+ 105 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
17
Number Of Timers
2
Program Memory Type
Flash
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.7 V
- Current page: 140 of 282
- Download datasheet (2Mb)
PS022827-1212
Infrared Encoder/Decoder Control Register Definitions
Caution:
The window remains open until the count again reaches 8 (that is, 24 baud clock periods
since the previous pulse was detected), giving the Endec a sampling window of minus four
baud rate clocks to plus eight baud rate clocks around the expected time of an incoming
pulse. If an incoming pulse is detected inside this window this process is repeated. If the
incoming data is a logical 1 (no pulse), the Endec returns to the initial state and waits for
the next falling edge. As each falling edge is detected, the Endec clock counter is reset,
resynchronizing the Endec to the incoming signal, allowing the Endec to tolerate jitter and
baud rate errors in the incoming datastream. Resynchronizing the Endec does not alter the
operation of the UART, which ultimately receives the data. The UART is only synchro-
nized to the incoming data stream when a Start bit is received.
All infrared endec configuration and status information is set by the UART Control regis-
ters as defined in the
To prevent spurious signals during IrDA data transmission, set the IREN bit in the UART
Control 1 Register to 1 to enable the Infrared Encoder/Decoder before enabling the GPIO
Port alternate function for the corresponding pin.
Universal Asynchronous Receiver/Transmitter
P R E L I M I N A R Y Infrared Encoder/Decoder Control Register
Z8 Encore! XP
Product Specification
section on page 99.
®
F082A Series
123
Related parts for Z8F041APH020SG2156
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: