S912XET512J3VALR Freescale Semiconductor, S912XET512J3VALR Datasheet - Page 231

• Manufacturer Part Number: S912XET512J3VALR
• Description: 16-bit Microcontrollers - MCU 16 BIT,512K FLASH
• Manufacturer: Freescale Semiconductor

Specifications of S912XET512J3VALR

• Rohs: yes
• Core: HCS12X
• Processor Series: MC9S12XE
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 512 KB
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 3.13 V to 5.5 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: LQFP-112
• Mounting Style: SMD/SMT

4.3.1.1
Read: Anytime
Write: Write of 1 clears flag, write of 0 ignored
If the AEF bit is set further violations are not captured into the MPU status registers. The status of the AEF
bit has no effect on the access restrictions, i.e. access restrictions for all masters are still enforced if the
AEF bit is set. Also, the non-maskable hardware interrupt for violating accesses coming from the S12X
CPU is generated regardless of the state of the AEF bit.
Freescale Semiconductor
Address: Module Base + 0x0000
Reset
NEXF
SVSF
Field
WPF
AEF
W
R
7
6
5
0
AEF
MPU Flag Register (MPUFLG)
0
7
Access Error Flag — This bit is the CPU access error interrupt flag. It is set if a CPU access violation has
occurred. At the same time this bit is set, all the other status flags in this register and the access violation
address bits in the MPUASTATn registers are captured. Clear this flag by writing a one.
Note: If a CPU access error is flagged and both the WPF bit and the NEXF bit are zero, the access violation
Note: While this bit is set, the CPU in supervisor state (“Master 0”) can read from and write to the peripheral
Note: This bit should only be cleared by an access from the S12X CPU. Otherwise, when using one of the
Write-Protect Violation Flag — This flag is set if the current CPU access violation has occurred because of
an attempt to write to memory configured as read-only. The WPF bit is read-only; it will be automatically
updated when the next access violation is flagged with the AEF bit.
No-Execute Violation Flag — This bit is set if the current CPU access violation has occurred because of an
attempt to fetch code from memory configured as No-Execute. The NEXF bit is read-only; it will be
automatically updated when the next access violation is flagged with the AEF bit.
Supervisor State Flag — This bit is set if the current CPU access violation occurred while the CPU was in
supervisor state. This bit is cleared if the current CPU access violation occurred while the CPU was in user
state. The supervisor state flag is read-only; it will be automatically updated when the next CPU access
violation is flagged with the AEF bit.
was caused by an access to memory not covered by the MPU descriptors.
register space even if there is no memory protection descriptor explicitly allowing this. This is to prevent
the case that the CPU cannot clear the AEF bit if the registers are write protected for the CPU in
supervisor state.
other masters (such as the XGATE) to clear this bit, the status flags and the address status registers
may not get updated correctly if a CPU access causes a violation in the same bus cycle.
WPF
0
6
MC9S12XE-Family Reference Manual Rev. 1.25
Figure 4-3. MPU Flag Register (MPUFLG)
Table 4-3. MPUFLG Field Descriptions
NEXF
0
5
0
0
4
Description
0
0
3
Chapter 4 Memory Protection Unit (S12XMPUV1)
0
0
2
0
0
1
SVSF
0
0
231