XC3S100E-4CP132GI XILINX [Xilinx, Inc], XC3S100E-4CP132GI Datasheet - Page 74

• Manufacturer Part Number: XC3S100E-4CP132GI
• Description: Spartan-3E FPGA Family: Complete Data Sheet
• Manufacturer: XILINX [Xilinx, Inc]

Functional Description
Table 49: Serial Master Mode Connections (Continued)
Voltage Compatibility
The PROM’s V
serial XCFxxS Platform Flash PROMs or 1.8V for the
serial/parallel XCFxxP PROMs.
Flash PROM’s V
age, ideally +2.5V. Both devices also support 1.8V and 3.3V
interfaces but the FPGA’s PROG_B and DONE pins require
special attention as they are powered by the FPGA’s
V
XAPP453: The 3.3V Configuration of Spartan-3 FPGAs for
additional information.
Supported Platform Flash PROMs
Table 50
PROM to program one Spartan-3E FPGA. A multiple-FPGA
daisy-chain application requires a
large enough to contain the sum of the various FPGA file
sizes.
Table 50: Number of Bits to Program a Spartan-3E
FPGA and Smallest Platform Flash PROM
74
DONE
PROG_B
V
CCAUX
Pin Name
XC3S1200E
XC3S1600E
Spartan-3E
XC3S100E
XC3S250E
XC3S500E
The FPGA’s VCCO_2 supply input and the Platform
FPGA
supply, nominally 2.5V. See application note
shows the smallest available Platform Flash
FPGA Direction
bidirectional I/O
CCINT
CCO
Open-drain
Configuration
Input
Number of
1,353,728
2,270,208
3,841,184
5,969,696
supply input must be the same volt-
supply must be either 3.3V for the
581,344
Bits
FPGA Configuration Done. Low during
configuration. Goes High when FPGA
successfully completes configuration.
Requires external 330 Ω pull-up resistor
to 2.5V.
Program FPGA. Active Low. When
asserted Low for 300 ns or longer, forces
the FPGA to restart its configuration
process by clearing configuration
memory and resetting the DONE and
INIT_B pins once PROG_B returns High.
Requires external 4.7 kΩ pull-up resistor
to 2.5V. If driving externally with a 3.3V
output, use an open-drain or
open-collector driver or use a current
limiting series resistor.
Platform Flash PROM
Smallest Available
Platform Flash
or 2 x XCF04S
XCF01S
XCF02S
XCF04S
XCF04S
XCF08P
Description
www.xilinx.com
The XC3S1600E requires an 8 Mbit PROM. Two solutions
are possible: either a single 8 Mbit XCF08P parallel/serial
PROM or two 4 Mbit XCF04S serial PROMs cascaded. The
two XCF04S PROMs use a 3.3V V
XCF08P requires a 1.8V V
not already have a 1.8V supply available, the two cascaded
XCF04S PROM solution is recommended.
CCLK Frequency
In Master Serial mode, the FPGA’s internal oscillator gener-
ates the configuration clock frequency. The FPGA provides
this clock on its CCLK output pin, driving the PROM’s CLK
input pin. The FPGA starts configuration at its lowest fre-
quency and increases its frequency for the remainder of the
configuration process if so specified in the configuration bit-
stream. The maximum frequency is specified using the
ConfigRate
maximum ConfigRate settings, approximately equal to
MHz, for various Platform Flash devices and I/O voltages.
For the serial XCFxxS PROMs, the maximum frequency
also depends on the interface voltage.
Table 51: Maximum ConfigRate Settings for Platform
Flash
Platform Flash
Part Number
XCF01S
XCF02S
XCF04S
XCF08P
XCF16P
XCF32P
Connects to PROM’s
chip-enable (CE) input.
Enables PROM during
configuration. Disables
PROM after configuration.
Must be High during
configuration to allow
configuration to start.
Connects to PROM’s CF pin,
allowing JTAG PROM
programming algorithm to
reprogram the FPGA.
During Configuration
bitstream generator option.
3.3V, 2.5V, or 1.8V
(VCCO_2, V
3.3V or 2.5V
I/O Voltage
CCINT
1.8V
DS312-2 (v3.4) November 9, 2006
supply. If the board does
CCO
CCINT
Pulled High via
external pull-up.
When High, indicates
that the FPGA
successfully
configured.
Drive PROG_B Low
and release to
reprogram FPGA.
)
Product Specification
After Configuration
Table 51
supply while the
ConfigRate
Maximum
Setting
25
12
25
shows the
R