AT32UC3C0512CAU Atmel Corporation, AT32UC3C0512CAU Datasheet - Page 896

• Manufacturer Part Number: AT32UC3C0512CAU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0512CAU

• Flash (kbytes): 512 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32117C–AVR-08/11
Table 32-7.
Table 32-8.
Table 32-9.
This field can be cleared by software. To avoid read-modify-write issues, the user should: freeze
the pipe, wait until the UPSTAX.PFREEZE is one, clear the PERSTA field in memory, and then
unfreeze the pipe.
31:24
23:21
ERCNT
• The control and status fields for the pipe and bank (Pn_CTR_STA_BK0/1):
• The control and status 1 of endpoint n (Pn_CTR_STA1):
31:19
-
-
– UNDERF: Underflow status for isochronous/Interrupt IN transfers. This status bit is
– OVERF: Overflow status for isochronous/interrupt OUT transfers. This status bit is
– CRCERR: CRC error status for isochronous IN transfers. See
– PERSTA: Pipe Error Status. See
–
–
– PDADDR: Should be set by the user. Device address for this pipe.
– ERCNT: Pipe Error Counter.
– CRC16ER: Is set if a CRC16 error occurs during an isochronous IN transaction.
– TOUTER: Is set if a Time-out error occurs during a USB transaction.
– PIDER: Is set if a PID error occurs during a USB transaction.
– DAPIDER: Is set if a Data PID error occurs during a USB transaction.
set by hardware at the current bank (where the IN packet should have been stored).
When a new successful transaction occurs this bit is overwritten to zero if
UPSTAX.ERRORFI has previously been cleared by software. See
on page
set by hardware at the current bank (where the OUT packet should have been
loaded). When a new successful transaction occurs this bit is overwritten to zero if
UPSTAX.ERRORFI has previously been cleared by software. See
on page
900.
PERMAX
page
PEPNUM
18
23:16
UNDERF
896) is larger than PERMAX, the UPSTAX.PERRI bit is set.
Status
20
CRC16ER
Pn_CTR_STA_BK0/1 structure
Pn_CTR_STA1 structure
PERSTA structure
: Should be set by the user. If the Pipe Error Counter (see
: Should be set by the user. Endpoint number for this pipe.
900.
900.
PERSTA
Status
17
OVERF
19
TOUTER
16
CRCERR
15:12
PERMAX
18
PIDER
“PERSTA structure”
11:8
15:0
PEPNUM
17
DAPIDER
Control
7
table.
Control
-
16
DTGLER
-
6:0
PDADDR
”CRC error” on page
”Data flow error”
”Data flow error”
Figure 32-9 on
AT32UC3C
896