AT32UC3C0512CAU Atmel Corporation, AT32UC3C0512CAU Datasheet - Page 89

• Manufacturer Part Number: AT32UC3C0512CAU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0512CAU

• Flash (kbytes): 512 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32117C–AVR-08/11
This allows the user to allocate separate handlers and priorities to the different interrupt types.
The interrupt request will be generated if the corresponding bit in the Interrupt Mask Register
(IMR) is set. Bits in IMR are set by writing a one to the corresponding bit in the Interrupt Enable
Register (IER), and cleared by writing a one to the corresponding bit in the Interrupt Disable
Register (IDR). The interrupt request remains active until the corresponding bit in the Interrupt
Status Register (ISR) is cleared by writing a one to the corresponding bit in the Interrupt Clear
Register (ICR).
• BOD50DET - 5V Brown out detection:
• BOD33DET - 3.3V Brown out detection:
• BODDET - 1.8V Brown out detection:
• PLL1LOCK - PLL1 locked:
• PLL0LOCK - PLL0 locked:
• RCOSC8MRDY - 8MHz / 1MHz RCOSC Ready:
• OSC32RDY - 32KHz Oscillator Ready:
• OSCR1DY - OSC1 Ready:
• OSCR0DY - OSC0 Ready:
– Set when a 0 to 1 transition on the PCLKSR.BOD50DET bit is detected.
– Set when a 0 to 1 transition on the PCLKSR.BOD33DET bit is detected.
– Set when a 0 to 1 transition on the PCLKSR.BODDET bit is detected.
– Set when a 0 to 1 transition on the PCLKSR.PLL1LOCK bit is detected.
– Set when an 0 to 1 transition on the PCLKSR.PLL0LOCK bit is detected.
– Set when a 0 to 1 transition on the PCLKSR.RCOSC8MRDY bit is detected.
– Set when a 0 to 1 transition on the PCLKSR.OSC32RDY bit is detected.
– Set when a 0 to 1 transition on the PCLKSR.OSC1RDY bit is detected.
– Set when a 0 to 1 transition on the PCLKSR.OSC0RDY bit is detected.
AT32UC3C
89