AT32UC3C0512CAU Atmel Corporation, AT32UC3C0512CAU Datasheet - Page 767

• Manufacturer Part Number: AT32UC3C0512CAU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0512CAU

• Flash (kbytes): 512 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

29.6.2.5
29.6.3
29.6.3.1
32117C–AVR-08/11
Message Handling
Wake-up mode
Message object structure
According to the CAN specification, a channel can be in error active, error passive or bus off
state. The bus state can be read in the CANFC.EMODE field:
Table 29-3.
This state depends on both transmit and receive counters value (TEC/REC), also available in
the CANFC register (see CAN specification for more details).
In this mode the CAN channel is a wake-up source for the CPU. Detection of a falling edge on
the CAN bus is interpreted as the start of frame (SOF) bit of the wake-up frame and will wake the
CPU.
In order to use this mode, execute the following steps:
Note 1: when channel is disabled PB registers are not cleared, user can resume current applica-
tion by enabling channel again.
Note 2: wake-up frame cannot be received. Moreover next frames cannot be received until CPU
is woken-up. Wake-up time depends on sleep modes (see sleep modes section).
Message Objects (MOb) are message descriptors, used to store and handle CAN frames. User
configures and gets status of MObs via user interface registers and writing and reading frames
into allocated RAM space
MObs are independent and are allocated to one channel.
EMODE
2 or 3
– Disable CAN channel by writing CANCTRL.CEN to zero
– Wait for channel disabled (CANSR.CES is cleared)
– Enable wake-up mode by writing CANCTRL.WKEN to one
– Optionally mask wake-up interrupt source by writing CANIMR.WKUPIM
– Enter sleep mode, stopping PB and CAN clocks
– Sleep
– Wake-up frame is detected, CANISR.WKUP is set and CPU is woken-up
– Clear CANISR.WKUP by writing it to zero
– Disable wake-up mode and enable CAN channel
0
1
Bus State Coding
error passive state
error active state
bus off state
State
(Section
29.6.1.5).
AT32UC3C
767