AT32UC3C0512CAU Atmel Corporation, AT32UC3C0512CAU Datasheet - Page 378

• Manufacturer Part Number: AT32UC3C0512CAU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0512CAU

• Flash (kbytes): 512 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

20.5.10
20.5.11
20.5.12
20.6
20.6.1
32117C–AVR-08/11
Performance Monitors
Priority
Error Handling
Peripheral Event Trigger
Measuring mechanisms
If more than one PDCA channel is requesting transfer at a given time, the PDCA channels are
prioritized by their channel number. Channels with lower numbers have priority over channels
with higher numbers, giving channel zero the highest priority.
If the Memory Address Register (MAR) is set to point to an invalid location in memory, an error
will occur when the PDCA tries to perform a transfer. When an error occurs, the Transfer Error
bit in the Interrupt Status Register (ISR.TERR) will be set and the DMA channel that caused the
error will be stopped. In order to restart the channel, the user must program the Memory
Address Register to a valid address and then write a one to the Error Clear bit in the Control
Register (CR.ECLR). If the Transfer Error interrupt is enabled, an interrupt request will be gener-
ated when an transfer error occurs.
Peripheral events can be used to trigger PDCA channel transfers. Peripheral Event synchroniza-
tions are enabled by writing a one to the Event Trigger bit in the Mode Register (MR.ETRIG).
When set, all DMA requests will be blocked until an peripheral event is received. For each
peripheral event received, only one data item is transferred. If no DMA requests are pending
when a peripheral event is received, the PDCA will start a transfer as soon as a peripheral event
is detected. If multiple events arrive while the PDCA channel is busy transferring data, an over-
flow condition will be signaled in the Peripheral Event System. Refer to the Peripheral Event
System chapter for more information.
Up tp two performance monitors allow the user to measure the activity and stall cycles for PDCA
transfers. To monitor a PDCA channel, the corresponding channel number must be written to
one of the MONnCH fields in the Performance Control Register (PCONTROL) and a one must
be written to the corresponding CHnEN bit in the same register.
Due to performance monitor hardware resource sharing, the two monitor channels should NOT
be programmed to monitor the same PDCA channel. This may result in UNDEFINED perfor-
mance monitor behavior.
Three different parameters can be measured by each channel:
These measurements can be extracted by software and used to generate indicators for bus
latency, bus load, and maximum bus latency.
Each of the counters has a fixed width, and may therefore overflow. When an overflow is
encountered in either the Performance Channel Data Read/Write Cycle registers (PRDATAn
and PWDATAn) or the Performance Channel Read/Write Stall Cycles registers (PRSTALLn and
PWSTALLn) of a channel, all registers in the channel are reset. This behavior is altered if the
Channel Overflow Freeze bit is one in the Performance Control register (PCONTROL.CHnOVF).
If this bit is one, the channel registers are frozen when either DATA or STALL reaches its maxi-
mum value. This simplifies one-shot readout of the counter values.
• The number of data transfer cycles since last channel reset, both for read and write
• The number of stall cycles since last channel reset, both for read and write
• The maximum latency since last channel reset, both for read and write
AT32UC3C
378