STM32W108HBU61TR STMicroelectronics, STM32W108HBU61TR Datasheet - Page 134

• Manufacturer Part Number: STM32W108HBU61TR
• Description: 16/32-BITS MICROS
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32W108HBU61TR

• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Applications: IEEE 802.15.4 Wireless
• Processing Unit: Microprocessor
• Operating Supply Voltage (min): 1.18V
• Operating Supply Voltage (typ): 1.25V
• Operating Supply Voltage (max): 1.32V
• Package Type: VFQFPN EP
• Pin Count: 40
• Mounting: Surface Mount
• Rad Hardened: No
• Core Processor: ARM® Cortex-M3™
• Program Memory Type: FLASH (128 kB)
• Controller Series: STM32W
• Ram Size: 8K x 8
• Interface: I²C, SPI, UART/USART
• Number Of I /o: 18
• Voltage - Supply: 1.18 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 40-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Compliant

General-purpose timers
134/220
filtered and not inverted.) The sequence of transitions of the two inputs is evaluated, and
generates count pulses as well as the direction signal. Depending on the sequence, the
counter counts up or down, and hardware modifies the TIM_DIR bit in the TIMx_CR1
register accordingly. The TIM_DIR bit is calculated at each transition on any input (TI1 or
TI2), whether the counter is counting on TI1 only, TI2 only, or both TI1 and TI2.
Encoder interface mode acts simply as an external clock with direction selection. This
means that the counter just counts continuously between 0 and the auto-reload value in the
TIMx_ARR register (0 to TIMx_ARR or TIMx_ARR down to 0 depending on the direction),
so TIMx_ARR must be configured before starting. In the same way, the capture, compare,
prescaler, and trigger output features continue to work as normal.
In this mode the counter is modified automatically following the speed and the direction of
the incremental encoder, and therefore its contents always represent the encoder's position.
The count direction corresponds to the rotation direction of the connected sensor.
summarizes the possible combinations, assuming TI1 and TI2 do not switch at the same
time.
Table 86.
An external incremental encoder can be connected directly to the MCU without external
interface logic. However, comparators are normally used to convert an encoder's differential
outputs to digital signals, and this greatly increases noise immunity. If a third encoder output
indicates the mechanical zero (or index) position, it may be connected to an external
interrupt input and can trigger a counter reset.
Figure 39
direction control. It also shows how input jitter is compensated for when both inputs are used
for counting. This might occur if the sensor is positioned near one of the switching points.
This example assumes the following configuration:
●
●
●
●
●
●
Counting on
TI1 only
Counting on
TI2 only
Counting on
TI1 and TI2
Active
edges
TIM_CC1S = 01 (TIMx_CCMR1 register, IC1FP1 mapped on TI1).
TIM_CC2S = 01 (TIMx_CCMR2 register, IC2FP2 mapped on TI2).
TIM_CC1P = 0 (TIMx_CCER register, IC1FP1 non-inverted, IC1FP1 = TI1).
TIM_CC2P = 0 (TIMx_CCER register, IC2FP2 non-inverted, IC2FP2 = TI2).
TIM_SMS = 011 (TIMx_SMCR register, both inputs are active on both rising and falling
edges).
TIM_CEN = 1 (TIMx_CR1 register, counter is enabled).
gives an example of counter operation, showing count signal generation and
Counting direction versus encoder signals
Level on opposite
signal (TI1FP1 for
TI2, TI2FP2 for
STM32W108HB, STM32W108CC, STM32W108CB and STM32W108CZ
High
High
High
TI1)
Low
Low
Low
Doc ID 16252 Rev 9
No Count
No Count
Rising
Down
Down
Up
Up
TI1FP1 signal
No Count
No Count
Falling
Down
Down
Up
Up
No Count
No Count
Rising
Down
Down
Up
Up
TI2FP2 signal
No Count
No Count
Falling
Down
Down
Table 86
Up
Up