DS3170 Maxim Integrated Products, DS3170 Datasheet - Page 43

no-image

DS3170

Manufacturer Part Number
DS3170
Description
Network Controller & Processor ICs DS3-E3 Single-Chip T ransceiver T3-E3 Fra
Manufacturer
Maxim Integrated Products
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS3170
Manufacturer:
DS
Quantity:
159
Part Number:
DS3170
Manufacturer:
DS
Quantity:
2 870
Part Number:
DS3170
Manufacturer:
Maxim Integrated
Quantity:
10 000
Part Number:
DS3170+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Part Number:
DS3170N
Manufacturer:
DS
Quantity:
3 283
Part Number:
DS3170N
Quantity:
737
Part Number:
DS3170N
Manufacturer:
Maxim Integrated
Quantity:
10 000
Part Number:
DS3170N+
Manufacturer:
MAXIM
Quantity:
301
Part Number:
DS3170N+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Part Number:
DS3170N+T&R
Manufacturer:
Maxim Integrated
Quantity:
10 000
Figure 8-16. DS3 Framed Mode Receive Serial Interface Pin Timing
Figure 8-17. E3 G.751 Framed Mode Receive Serial Interface Pin Timing
Figure 8-18. E3 G.832 Framed Mode Receive Serial Interface Pin Timing
8.3.4 Microprocessor Interface Functional Timing
8.3.4.1
NOTE: The transmit and receive order of the address and data bits are selected by the D[5]/SPI_SWAP pin. The
R/W (read/write) MSB bit and B (burst) LSB bit position is not effected by the D[5]/SPI_SWAP pin setting.
8.3.4.1.1
When CPHA = 0, CS may be de-asserted between accesses. An access is defined as one or two control bytes
followed by a data byte. CS cannot be de-asserted between the control bytes, or between the last control byte and
the data byte. When CPHA = 0, CS may also remain asserted between accesses. If it remains asserted and the
BURST bit is set, no additional control bytes are expected after the first control byte(s) and data are transferred. If
the BURST bit is set, the address will be incremented for each additional byte of data transferred until CS is de-
asserted. If CS remains asserted and the BURST bit is not set, a control byte(s) is expected following the data byte,
and the address for the next access will be received from that. Anytime CS is de-asserted, the BURST access is
terminated.
When CPHA = 1, CS may remain asserted for more than one access without being toggled high and then low
again between accesses. If the BURST bit is set, the address should increment and no additional control bytes are
DS3 RGCLK
E3 RGCLK
RCLKO or
RCLKO or
DS3 RSER
DS3 RDEN
E3 RGCLK
RCLKO or
E3 RSER
E3 RDEN
RSOFO
E3 RSER
E3 RDEN
RSOFO
RCLKI
RCLKI
RCLKI
RSOF
SPI Functional Timing Diagrams
SPI Transmission Format and CPHA Polarity
1
1
1
2
2
2
3
3
3
X1
4
4
4
5
5
5
6
6
FA1 11110110
6
FAS 1111010000
7
7
7
8
8
8
9
9
9
43 of 230
10
10
10
11
11
11
12
12
12
13
13
13
FA2 00101000
A
14
14
14
15
15
N
15
DS3170 DS3/E3 Single-Chip Transceiver
16
17
18
19
20

Related parts for DS3170