DS3170 Maxim Integrated Products, DS3170 Datasheet - Page 100
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS3170
Manufacturer Part Number
DS3170
Description
Network Controller & Processor ICs DS3-E3 Single-Chip T ransceiver T3-E3 Fra
Manufacturer
Maxim Integrated Products
Datasheet
1.DS3170.pdf
(230 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS3170N+
Manufacturer:
MAXIM
Quantity:
301
Company:
Part Number:
DS3170N+T&R
Manufacturer:
Maxim Integrated
Quantity:
10 000
The Trail Trace Controller extracts/inserts E3-G.832 trail access point identifiers using a 16-byte register(one for
transmit, one for receive).
The Trail Trace Controller demaps a 16-byte trail trace identifier from the E3-G.832 datastream in the receive
direction and maps a trace identifier into the E3-G.832 datastream in the transmit direction.
The receive direction inputs the trace ID data stream, performs trace ID processing, and stores the trace identifier
data in the data storage using line timing. It removes trace identifier data from the data storage and outputs the
trace identifier data to the microprocessor via the microprocessor interface using register timing. The data is forced
to all ones during LOS, LOF and AIS detection to eliminate false messages
The transmit direction inputs the trace identifier data from the microprocessor via the microprocessor interface and
stores the trace identifier data in the data storage using register timing. It removes the trace identifier data from the
data storage, performs trace ID processing, and outputs the trace ID data stream. Refer to
location of the Trail Trace Controller with the DS3170 device.
Figure 10-20. Trail Trace Controller Block Diagram
10.8.2 Features
•
•
•
•
•
•
•
•
10.8.3 Functional Description
The bits in a byte are received most significant bit (MSB) first and least significant bit (LSB) last. When they are
output serially, they are output MSB first and LSB last. The bits in a byte in an incoming signal are numbered in the
Clock Rate
Programmable trail trace ID – The trail trace ID controller can be programmed to handle a 16-byte trail trace
identifier (trail trace mode).
Programmable transmit trace ID – All sixteen bytes of the transmit trail trace identifier are programmable.
Programmable receive expected trace ID – A 16-byte expected trail trace identifier can be programmed.
Both a mismatch and unstable indication are provided.
Programmable trace ID multiframe alignment – The transmit side can be programmed to perform trail trace
multiframe alignment insertion. The receive side can be programmed to perform trail trace multiframe
synchronization.
Programmable bit reordering – The trace identifier data can be output MSB first or LSB first from the data
storage.
Programmable data inversion – The trace identifier data can be inverted immediately after trace ID
processing on the transmit side, and immediately before trail ID processing on the receive side.
Fully independent transmit and receive sides
Fully independent Line side and register interface timing – The data storage can be read from or written to
via the microprocessor interface while all line side clocks and signals are inactive, and read from or written to
via the line side while all microprocessor interface clocks and signals are inactive.
Receive
Transmit
DS3/E3
DS3/E3
Adapter
LIU
LIU
Encoder
Decoder
B3ZS/
B3ZS/
HDB3
HDB3
TUA1
TAIS
IEEE P1149.1
Access Port
JTAG Test
FEAC
DS3 / E3
Framer
DS3 / E3
Transmit
Receive
Formatter
Buffer
Trace
Trail
HDLC
100 of 230
GEN
UA1
DS3170 DS3/E3 Single-Chip Transceiver
RX BERT
TX BERT
Microprocessor
Interface
Figure 10-20
for the