F39-EU1E Omron, F39-EU1E Datasheet - Page 601

F3S-B OPTIONAL PROGRAMMING KIT

F39-EU1E

Manufacturer Part Number
F39-EU1E
Description
F3S-B OPTIONAL PROGRAMMING KIT
Manufacturer
Omron
Datasheet

Specifications of F39-EU1E

Leaded Process Compatible
No
Peak Reflow Compatible (260 C)
No
Light Curtain Type
Safety
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11. Install the actuator and switch at an appropriate distance so that
12. Where two or more Switches are mounted side-by-side, they must
13. Check that the machine is stopped whenever the interlocked
14. Do not mount the switch and actuator on magnetic materials,
15. Tighten all screws to the specified torque by using non-magnetic
16. Wiring
17. Mounting
0 to 5 mm
5 mm or longer
Distance from surface of
they do not create a gap that provides access to the hazard.
be no closer than 25 mm.
guard door is open.
otherwise it may affect the operating distance.
M4 screws and washer for the installation of the switch and
actuator. After installation and using, the actuator and switch
fixing screws must be coated with tamper proof varnish or similar
compound. Using anaerobic locking compounds can have a
detrimental effect on the plastic switch case if the compounds
come into contact with the switch case.
1. Use the following to wire to the product.
2. When an auxiliary output is not used, cut off the wiring and
Mount the G9SX-NS to a DIN rail using End Plates (PFP-M, not
included with the product) so that the G9SX-NS does not fall off of
the rails due to vibration or other causes, especially when the
length of DIN railing is short compared to the width of the
G9SX-NS@.
Stranded wire (flexible wire): 0.2 to 2.5 mm
AWG12)
Solid wire (steel wire): 0.2 to 2.5 mm
cover it with tape so that it does not contact other terminals.
magnetic body
Correct
http://www.ia.omron.com/
Switch
25 mm min.
Reduce to approx. 90% of
original value.
No influence.
Incorrect
Operating distance
2
(AWG24 to AWG12)
Actuator
2
(AWG24 to
18. The following space must be provided around the G9SX-NS@ to
19. Wiring
20. Connecting G9SX-EX@-@ Expansion Units
21. Use cables with a length of less than 100 m total to connect the
22. Set the time duration of OFF-delay to an appropriate value that
enable applying the rated current to the outputs of the G9SX-
NS@, to ensure sufficient ventilation, and to enable wiring:
1. At least 25 mm between side surfaces of the G9SX-NS@
2. At least 50 mm above the top surface of the G9SX-NS@ and
1. G9SX-NS@-RT (with Screw Terminals)
2. G9SX-NS@-RC (with Spring-cage Terminals)
3. Logical AND Connections
1. Remove the terminating connector from the connector on the
2. Connect the terminating connector to the connector on the
3. Do not remove the terminating connector or connecting cables
4. Before applying the supply voltage, confirm that the connectors
5. All of the Expansion Units must be supplied with its specified
safety inputs, feedback/reset inputs, and logical AND connection
inputs and outputs.
does not cause the loss of safety functions of system.
below the bottom surface of the G9SX-NS@.
• Use the following to wire the G9SX-NS@-RT.
• Tighten each screw to the specified torque of 0.5 to 0.6 N
• Strip the wire for no longer than 7 mm.
• Use the following to wire the G9SX-NS@-RC.
• It is recommended that insulation-covered bar terminals
• Use VCTF cables or shielded cables for logical AND connect
G9SX-NSA222-T03@. Insert the connector on the connecting
cable of Expansion Unit into the connector on the G9SX-NSA222-
T03-@.
Expansion Unit at the end position.
When the G9SX-NSA222-T03-@ is used without Expansion
Units, leave the terminating connector on the G9SX-NSA222-
T03-@.
of Expansion Units while the system is operating.
are locked firmly.
voltages within 10 s after the connected G9SX-NSA222-T03-@
is supplied with voltage.
Otherwise, the G9SX-NSA222-T03-@ will detect a power
supply error for the Expansion Units.
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
or the G9SX-NS@ may malfunction or generate heat.
(DIN 46228-4 compatible) be connected to stranded wires
before connecting the wires.
ions between Units.
Solid wire
(steel wire)
Stranded wire
(flexible wire)
Solid wire
(steel wire)
Stranded wire
(flexible wire)
25 mm min.
0.2 to 2.5 mm
AWG12)
0.2 to 2.5 mm
AWG12)
0.2 to 2.5 mm
AWG12)
0.2 to 2.5 mm
AWG12)
25 mm min.
D40A/G9SX-NS
2
2
2
2
50 mm min.
50 mm min.
(AWG24 to
(AWG24 to
(AWG24 to
(AWG24 to
·
m,
26

Related parts for F39-EU1E