UPD78F1001GA-HAA-AX Renesas Electronics America, UPD78F1001GA-HAA-AX Datasheet - Page 979

• Manufacturer Part Number: UPD78F1001GA-HAA-AX
• Description: MCU 16BIT 78K0R/KX3-L 44-TQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Kx3-Lr

Specifications of UPD78F1001GA-HAA-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Kx3-L
manipulation such as writing and erasing via a dedicated single-line UART. To write the flash memory off-board, a
dedicated program adapter (FA series) is necessary.
26.3 Communication Mode
communication using the TOOL0 pin via a dedicated single-line UART of the 78K0R/Kx3-L.
FP5, FL-PR5, or MINICUBE2 for details.
R01UH0106EJ0300 Rev.3.00
Oct 01, 2010
26.2 Programming Environment
The environment required for writing a program to the flash memory of the 78K0R/Kx3-L is illustrated below.
A host machine that controls the dedicated flash memory programmer is necessary.
To interface between the dedicated flash memory programmer and the 78K0R/Kx3-L, the TOOL0 pin is used for
Communication between the dedicated flash memory programmer and the 78K0R/Kx3-L is established by serial
The dedicated flash memory programmer generates the following signals for the 78K0R/Kx3-L. See the manual of PG-
Transfer rate: 115,200 bps, 250,000 bps, 500,000 bps, 1 Mbps
Notes 1. When using a transfer rate of 1 Mbps, do not use the wide voltage mode.
Host machine
2. This pin is not required to be connected when using PG-FP5 or FL-PR5.
3. Connect SI/RxD or SO/TxD when using QB-MINI2.
PG-FP5, FL-PR5
memory programmer
Figure 26-10. Communication with Dedicated Flash Memory Programmer
Dedicated flash
Figure 26-9. Environment for Writing Program to Flash Memory
RS-232C
QB-MINI2
USB
PG-FP5, FL-PR5
SI/RxD
SO/TxD
memory programmer
Dedicated flash
/RESET
FLMD0
Notes 2, 3
GND
Note 3
V
DD
QB-MINI2
Note 1
TOOL0 (dedicated single-line UART)
V
V
RESET
TOOL0
FLMD0
DD
SS
FLMD0
RESET
/EV
/EV
V
V
DD
SS
DD
SS
CHAPTER 26 FLASH MEMORY
/EV
/EV
SS0
DD0
/EV
/EV
78K0R/Kx3-L
SS1
DD1
78K0R/Kx3-L
979