UPD78F1001GA-HAA-AX Renesas Electronics America, UPD78F1001GA-HAA-AX Datasheet - Page 409

• Manufacturer Part Number: UPD78F1001GA-HAA-AX
• Description: MCU 16BIT 78K0R/KX3-L 44-TQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Kx3-Lr

Specifications of UPD78F1001GA-HAA-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Kx3-L
R01UH0106EJ0300 Rev.3.00
Oct 01, 2010
Address: F0190H, F0191H (TMR00) to F019EH, F019FH (TMR07)
TMRmn
Symbol
Notes 1. In one-count mode, interrupt output (INTTMmn) when starting a count operation and TOmn output are not
Remark m: Unit number (m = 0, 1), n: Channel number (n = 0 to 7)
F01C8H, F01C9H (TMR10) to F01CEH, F01CFH (TMR13)
The operation of the MDmn0 bit varies depending on each operation mode (see table below).
• Interval timer mode
• Capture mode
• Event counter mode
• One-count mode
• Capture & one-count mode
CKS
mn3
2. If the start trigger (TSmn = 1) is issued during operation, the counter is cleared, an interrupt is generated,
MD
mn
15
0
0
0
1
1
(0, 1, 0)
(0, 1, 1)
(1, 0, 0)
(1, 1, 0)
(0, 0, 0)
(Value set by the MDmn3 to MDmn1 bits
controlled.
and recounting is started.
However, in case of the timer output pin (TOmn), mn changes as below.
78K0R/KC3-L (40-pin):
78K0R/KC3-L (44-pin, 48-pin):
78K0R/KD3-L, 78K0R/KE3-L:
78K0R/KF3-L, 78K0R/KG3-L:
Other than above
mn2
MD
14
0
1
1
0
1
0
(see table above))
Operation mode
mn1
MD
Figure 8-11. Format of Timer Mode Register mn (TMRmn) (3/3)
13
0
0
1
0
0
0
Other than above
Note 1
CCS
mn0
MD
1/0
1/0
1/0
mn
12
0
0
Interval timer mode
Capture mode
Event counter mode
One-count mode
Capture & one-count mode
Setting prohibited
MAST
ERmn
11
Operation mode of channel n
STS
mn2
10
STS
mn1
mn = 02 to 07
mn = 00 to 07
mn = 00 to 07
mn = 00 to 07, 10 to 13
9
mn0
MD
0
1
0
0
1
0
STS
mn0
8
Timer interrupt is not generated when counting is started
(timer output does not change, either).
Timer interrupt is generated when counting is started
(timer output also changes).
Timer interrupt is not generated when counting is started
(timer output does not change, either).
Start trigger is invalid during counting operation.
At that time, interrupt is not generated, either.
Start trigger is valid during counting operation
At that time, interrupt is also generated.
Timer interrupt is not generated when counting is started
(timer output does not change, either).
Start trigger is invalid during counting operation.
At that time interrupt is not generated, either.
Setting prohibited
After reset: 0000H
mn1
CIS
7
Setting of starting counting and interrupt
Counting down
Counting up
Counting down
Counting down
Counting up
mn0
CIS
Count operation of TCR
6
CHAPTER 8 TIMER ARRAY UNIT
5
0
R/W
4
0
mn3
MD
3
Possible
Possible
Possible
Impossible
Possible
Independent operation
mn2
MD
2
Note 2
mn1
.
MD
1
mn0
MD
0
409