M306N4FGTFP#U0 Renesas Electronics America, M306N4FGTFP#U0 Datasheet - Page 141

• Manufacturer Part Number: M306N4FGTFP#U0
• Description: MCU 5V 256K T-TEMP PB-FREE 100-Q
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGTFP#U0

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
Table 13.4 One-shot Timer Mode Specifications
i = 0 to 4
j = i - 1, except j = 4 if i = 0
k = i + 1, except k = 0 if i = 4
Count source
Count operation
Divide ratio
Count start condition
Count stop condition
Interrupt request generation timing When the counter reaches 0000h
TAiIN pin function
TAiOUT pin function
Read from timer
Write to timer
Select function
13.1.3 One-shot Timer Mode
In one-shot timer mode, the timer is activated only once by one trigger. When the trigger occurs, the timer
starts up and continues operating for a given period. Table 13.4 lists the One-shot Timer Mode Specifications.
Figure 13.11 shows Registers TA0MR to TA4MR in One-shot Timer Mode.
Apr 14, 2006
Item
page 117 of 376
f1, f2, f8, f32, fC32
• Down-count
• When the counter reaches 0000h, it stops counting after reloading a new value
• If a trigger occurs when counting, the timer reloads a new count and restarts counting
1/n
However, the counter does not work if the divide-by-n value is set to 0000h.
The TAiS bit in the TABSR register = 1 (count starts) and one of the following
triggers occurs.
• External trigger input from the TAiIN pin
• Timer B2 overflow or underflow,
• The TAiOS bit in the ONSF register is set to 1 (timer starts)
• When the counter is reloaded after reaching 0000h
• TAiS bit is set to 0 (count stops)
I/O port or trigger input
I/O port or pulse output
An undefined value is read by reading the TAi register
• When not counting and until the 1st count source is input after counting start
• When counting (after 1st count source input)
• Pulse output function
Timer Aj overflow or underflow,
Timer Ak overflow or underflow
Value written to the TAi register is written to both reload register and counter
Value written to the TAi register is written to only reload register
(Transferred to counter when reloaded next)
The timer outputs a low when not counting and a high when counting.
n : set value of the TAi register
Specification
0000h to FFFFh
13. Timers