ATSAM3S4CA-AU Atmel, ATSAM3S4CA-AU Datasheet - Page 930

• Manufacturer Part Number: ATSAM3S4CA-AU
• Description: IC MCU 32BIT 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S4CA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 16x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 79
• Ram Memory Size: 48KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Cpu Family: AT91
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 64MHz
• Total Internal Ram Size: 48KB
• # I/os (max): 79
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.62V
• On-chip Adc: 16-chx12-bit
• On-chip Dac: 2-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

37.6.1.3
930
SAM3S Preliminary
USB Transfer Event Definitions
As indicated below, transfers are sequential events carried out on the USB bus.
Table 37-5.
Notes:
A status transaction is a special type of host-to-device transaction used only in a control transfer.
The control transfer must be performed using endpoints with no ping-pong attributes. According
to the control sequence (read or write), the USB device sends or receives a status transaction.
Control Transfers
Interrupt IN Transfer
(device toward host)
Interrupt OUT Transfer
(host toward device)
Isochronous IN Transfer
(device toward host)
Isochronous OUT Transfer
(host toward device)
Bulk IN Transfer
(device toward host)
Bulk OUT Transfer
(host toward device)
1. Setup Transaction
2. Data IN Transaction
3. Data OUT Transaction
1. Control transfer must use endpoints with no ping-pong attributes.
2. Isochronous transfers must use endpoints with ping-pong attributes.
3. Control transfers can be aborted using a stall handshake.
USB Transfer Events
(1) (3)
(2)
(2)
• Setup transaction > Data IN transactions > Status
• Setup transaction > Data OUT transactions > Status
• Setup transaction > Status IN transaction
• Data IN transaction > Data IN transaction
• Data OUT transaction > Data OUT transaction
• Data IN transaction > Data IN transaction
• Data OUT transaction > Data OUT transaction
• Data IN transaction > Data IN transaction
• Data OUT transaction > Data OUT transaction
OUT transaction
IN transaction
6500C–ATARM–8-Feb-11